Jump to content

Search the Community

Showing results for tags 'connection sharing error'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Talk
    • Everything Else
    • Gaming
    • Questions
    • Business and Enterprise IT
    • Security
    • Hacks & Mods
    • Applications & Coding
    • Trading Post
  • Hak5 Gear
    • Hak5 Cloud C²
    • WiFi Pineapple Mark VII
    • USB Rubber Ducky
    • Bash Bunny
    • Key Croc
    • Packet Squirrel
    • Shark Jack
    • Signal Owl
    • LAN Turtle
    • Screen Crab
    • Plunder Bug
  • O.MG (Mischief Gadgets)
    • O.MG Cable
    • O.MG DemonSeed EDU
  • WiFi Pineapple (previous generations)
    • WiFi Pineapple TETRA
    • WiFi Pineapple NANO
    • WiFi Pineapple Mark V
    • WiFi Pineapple Mark IV
    • Pineapple Modules
    • WiFi Pineapples Mark I, II, III
  • Hak5 Shows
  • Community
    • Forums and Wiki
    • #Hak5
  • Projects
    • SDR - Software Defined Radio
    • Community Projects
    • Interceptor
    • USB Hacks
    • USB Multipass
    • Pandora Timeshifting

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests


Enter a five letter word.

Found 2 results

  1. Hello guys, First of all I want to say hi as I'm new to forum and WP. I also want to mention that I looked for the help in other topics but unfortunately was unable to overcome my issue. I have a problem with connection sharing (I have access to internet, however nano does not - impossible to load bulletins). I used the script and it worked the first time. After I left nano scanning for a few minutes the connection was gone. Client mode works fine. Using the script again did not help. Adding new default routes to Kali did not help. Factory rested did't as well. I don't know how to resolve this... My system info: Kali Rolling edition (not vm) nano: v 2.5.2 script: wp6.sh route on kali outputs: Destination Gateway Genmask Flags Metric Ref Use Iface default _gateway 0.0.0.0 UG 600 0 0 wlan0 10.0.0.0 0.0.0.0 255.255.255.0 U 600 0 0 wlan0 172.16.42.0 0.0.0.0 255.255.255.0 U 100 . 0 0 wlan0 ip route: default via 10.0.0.1 dev wlan0 proto dhcp metric 600 10.0.0.0/24 dev wlan0 proto kernel scope link src 10.0.0.11 metric 600 172.16.42.0/24 dev eth1 proto kernel scope link src 172.16.42.109 metric 100 Wp6.sh configuration: Saved Settings: Share Internet connection from wlan0 to WiFi Pineapple at eth1 through default gateway 10.0.0.1 (nano is indeed on eth1) ifconfig on eth1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 172.16.42.109 netmask 255.255.255.0 broadcast 172.16.42.255 (...) also from management page: Networking tab > route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 172.16.42.42 0.0.0.0 UG 0 0 0 br-lan 172.16.42.0 * 255.255.255.0 U 0 0 0 br-lan "upadte route" shows in grey: 172.16.42.42 Please help me deal with this... and sorry if something's stupid happening, I'm still a learner. let me know if more data is needed. Thanks!
  2. Hello, I have greatly enjoyed my Pineapple thus far and am extremely impressed with this awesome tool. I have a question for you. I am running Ubuntu 12.04 64 bit with my pineapple. I have attempted many times to run the wp5 scripts (using sudo) and receive the print below. Just in case there are any questions about my configuration, I have also posted ifconfig printouts at the bottom. After the scripts runs, I can no longer connect to the internet or the pineapple. I also have a side question about the SD card, does this card get flashed with each boot. I have stored some data on it that seems to be erased with each boot. (infusions and such) Pineapple Netmask [255.255.255.0]: Pineapple Network [172.16.42.0/24]: Interface between PC and Pineapple [eth0]: Interface between PC and Internet [wlan0]: Internet Gateway [172.16.42.1]: 172.16.69.2 IP Address of Host PC [172.16.42.42]: 172.16.69.128 IP Address of Pineapple [172.16.42.1]: _ . ___ \||/ Internet: 172.16.69.2 - wlan0 ( _ )_ <--> [___] <--> ,<><>, Computer: 172.16.69.128 (_ _(_ ,) \___\ '<><>' Pineapple: 172.16.42.0/24 - eth0 iptables: Too many links. SIOCDELRT: No such process Browse to http://172.16.42.1:1471 IFCONFIG PRINTOUT wlan0 Link encap:Ethernet HWaddr inet addr:172.16.69.128 Bcast:172.16.69.255 Mask:255.255.255.0 eth0 Link encap:Ethernet HWaddr inet addr:172.16.42.130 Bcast:172.16.42.255 Mask:255.255.255.0 Thanks for you time. Ill keep playing around with it an will post a solution if I find one. - Justin
×
×
  • Create New...