Jump to content

Search the Community

Showing results for tags 'Brick'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Talk
    • Everything Else
    • Gaming
    • Questions
    • Business and Enterprise IT
    • Security
    • Hacks & Mods
    • Applications & Coding
    • Trading Post
  • Hak5 Gear
    • Hak5 Cloud C²
    • WiFi Pineapple Mark VII
    • USB Rubber Ducky
    • Bash Bunny
    • Key Croc
    • Packet Squirrel
    • Shark Jack
    • Signal Owl
    • LAN Turtle
    • Screen Crab
    • Plunder Bug
  • O.MG (Mischief Gadgets)
    • O.MG Cable
    • O.MG DemonSeed EDU
  • WiFi Pineapple (previous generations)
    • WiFi Pineapple TETRA
    • WiFi Pineapple NANO
    • WiFi Pineapple Mark V
    • WiFi Pineapple Mark IV
    • Pineapple Modules
    • WiFi Pineapples Mark I, II, III
  • Hak5 Shows
  • Community
    • Forums and Wiki
    • #Hak5
  • Projects
    • SDR - Software Defined Radio
    • Community Projects
    • Interceptor
    • USB Hacks
    • USB Multipass
    • Pandora Timeshifting

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests


Enter a five letter word.

Found 10 results

  1. I tried updating my bashbunny to 1.4 today, and it was going well.. Then, after i ejected it and put it back in to start the update it started flashing a "police" pattern. I am back on version 1.0 and no matter what update i download, i am not able to go up. I would really like some help... I don't understand what is wrong.
  2. Hi guys, I bought a MK5 a few months ago and it worked like a charm ... it's been turned off for a while and today, when I tried to turn it on again, I got stuck in a boot loop ( green led fixed and blue blinking ). I tried the unbrick procedure described here more than once ( switch pins setup, upload factory.bin, switch pins back, reboot ) but when I try to reboot I get the same results ( of course I've waited more than 5 minutes for it to stop ). Any hints would be very appreciated as I really need this device working for my job.
  3. How does one get an RMA number for a defective MK5?
  4. I see a lot of posts saying that their device is bricked, but I never see anyone say how it looks when it's bricked. Can someone tell me how a device appears when the device is "bricked"? Thanks guys once again! :)
  5. Bought a Mark V at DefCon yesterday. Took it to my room and booted it up; saw the SSID, logged in and changed the password - that was all initially. Today I had to change hotels, and decided I would try to upgrade to 2.0 firmware. However this time when I booted up, I get no ethernet connection to my laptop or a switch. Also, no SSID is seen, though the AR9331 LED lights up as if it is on. After messing around for a while, I decided to try the "unbricking" instructions on the website. With the DIP switches set to the appropriate mode (up, up, up, up, down), it boots and I get an ethernet conn
  6. Morning All - I've been searching the forum for some guidance, but nothing's worked so far. I hope this is the place for this request. I've been running the MkV for a few months - no issues. Then it had a power failure during a firmware upgrade (laptop plugged in - no battery - small child - sigh) and the MkV looks bricked. Attempt 1: Read the unbrick instructions, grabbed firmware bin, rebooted (UUUUD) - solid green, solid red, no B or A Gave laptop static ip 192.168.1.2, can't connect via ethernet, no wifi access Attempt 2: Tried reboot and reset (UDDUU) - solid green, flashing RBG - n
  7. The main problem is that the pineapple address won't load (172.16.42.1:1471) Pineapple Hardware Version: Mark IV Pineapple Software Version: I beleive 2.8.0 (I remember attempting to update) OS used to connect to the pineapple: Macintosh (MacBook Pro) and Linux (Kali Linux [ran through Virtual Box]) Network layout of how your setup is connected (including IP information): In Mac's network settings IP Address: 172.16.42.42 Subnet Mask: 255.255.255.0 Router: Nothing DNS Server: 8.8.8.8 Search Domains: Nothing All the tools/options that are running on the pineapple when the issue happened: It wa
  8. I tried using the instructions on the wiki for using the wifi pineapple with Mac OSX ICS. Now the wifi wont work, and I have no way to get into the pineapple. I tried both ethernet ports on the pineapple and my macbook air keeps on giving it's self self assigned IP addresses. Currently I am trapped in an airport with an almost 5 hour delay. [EDIT] I have tried sshing to 192.168.2.254 using both ports to no avail!
  9. I upgraded my mark IV from 2.5 to 2.7 and during upgrade, the device lost power and now the device is not broadcasting a SSID, neither ether port will allow me to talk with the device. i have tried the new 1471 UI address, the device simply does not communicate with anything. am I SOL or is there a way to fix. this is a user error problem, meaning user has spastic cat who knocked jasager off desk unplugging it. any help would be awesome. thank you
  10. I just bricked my pineapple mark IV. I made a firmware flashing and my pc Rebooted in the sametime..... now I can't access my router pineappe when i try, i just reach the "redirect.php" in loop :( is there a way to fix it?
×
×
  • Create New...