Jump to content

MGideon

Members
  • Content Count

    3
  • Joined

  • Last visited

About MGideon

  • Rank
    Newbie
  1. Route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 172.16.42.42 0.0.0.0 UG 0 0 0 br-lan 172.16.42.0 * 255.255.255.0 U 0 0 0 br-lan Default RouteInterface br-laneth0wlan0wlan0-1 Update Route Access Points AP Channel 1234567891011 Management SSID Management PSK Hide Management AP Disable Management AP Open SSID Maximum Clients Hide Open SSID Update Access Points OUI Lookup MAC Address Lookup WiFi Client Mode Interface wlan1mon Scan Note: Choosing wlan1 will interfere with PineAP. MAC Addresses Interface wlan0wlan0-1wlan1mon Current MAC New MAC Set New MAC Set Random MAC Note: Changing MAC addresses will restart the WiFi. Advanced Hostname Update br-lan Link encap:Ethernet HWaddr 00:C0:CA:A9:94:61 inet addr:172.16.42.1 Bcast:172.16.42.255 Mask:255.255.255.0 inet6 addr: fd1a:49f:408d::1/60 Scope:Global inet6 addr: fe80::2c0:caff:fea9:9461/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5838 errors:0 dropped:0 overruns:0 frame:0 TX packets:8272 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2301555 (2.1 MiB) TX bytes:3816238 (3.6 MiB) eth0 Link encap:Ethernet HWaddr 00:C0:CA:A9:94:61 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5807 errors:0 dropped:2 overruns:0 frame:0 TX packets:8274 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2378409 (2.2 MiB) TX bytes:3818996 (3.6 MiB) Interrupt:4 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:227 errors:0 dropped:0 overruns:0 frame:0 TX packets:227 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:15450 (15.0 KiB) TX bytes:15450 (15.0 KiB) wlan0 Link encap:Ethernet HWaddr 00:C0:CA:A9:88:A9 inet6 addr: fe80::2c0:caff:fea9:88a9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:30 errors:0 dropped:0 overruns:0 frame:0 TX packets:554 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4938 (4.8 KiB) TX bytes:148580 (145.0 KiB) wlan0-1 Link encap:Ethernet HWaddr 02:C0:CA:A9:88:A9 inet6 addr: fe80::c0:caff:fea9:88a9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:537 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:146613 (143.1 KiB) wlan1mon Link encap:UNSPEC HWaddr 00-C0-CA-A9-8E-A4-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:121581 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:29896911 (28.5 MiB) TX bytes:0 (0.0 B)
  2. I have it set to WPA2. I reset everything and tried again. Now I can deauth, but my device (phone) sits in the associated clients area. If I turn off wifi and back on (on my phone) it goes back to my AP in the recon list. It looks like I can only insert an image from a URL. I took the screen shots, but need to figure out how to post them.
  3. Firmware 2.7.0. I got my Nano up and running but I'm not getting any clients to connect. I ran a recon, and added a spare laptop and my phone the PineAP filter along with my AP. I created a filter and allowed only those two devices. I deauthed both devices. My phone re-connects to its regular AP, my laptop shows up under unassociated clients. Neither connect to my nano. Just as a test, I removed all filters and deauthed my phone again (can't deauth the laptop from the GUI, but I did disconnect and reconnect the laptop's wifi from the laptop) but neither connect. I'm still getting used to the interface, but I may have missed something. I also downloaded a Deauth module with the same results. Thanks for any input, Mike
×
×
  • Create New...