Jump to content

coyotlgw

Active Members
  • Content Count

    29
  • Joined

  • Last visited

  • Days Won

    3

Everything posted by coyotlgw

  1. I feel your pain... i have been trying to get my Nano to work on-and-off for about a year now. I get a few moments of joy when it is working, but after the first or second scan it just stops working. I have swapped out several SD cards, flashed the firmware many times, and tried several computers. Each thread I post ends after I post whatever logs are requested. I think that everything works when it leaves the shop but components may deteriorate when heated up by use. I wish Hak5 had a support team instead of croudsourcing it. UPDATE 30 JUL: Tracked down Seb at DEF CON, Hak5 stands behind their products... I appreciate the help
  2. Sorry, did not see your response... my results: 20170621 22:10 booted up, ran recon, successful for 15 second scan, four SSIDs 2 minute scan took five minutes, returned "No scan results" 22:19 ssh-ed in, ran airmon-ng start wlan1 Noticed that PineAP Daemon: Enabled... switched off, saved autostart config Started 30 second scan, 30 seconds to scan, two more minutes at 100% before "No scan results" back to terminal, ran pinesniffer wlan1mon 60 0 /tmp/test results: root@Pineapple:~# airmon-ng start wlan1 Found 1 processes that could cause trouble. If airodump-ng, aireplay-ng or airtun-ng stops working after a short period of time, you may want to kill (some of) them! 2686 root 1376 S grep wpa_action\|wpa_supplicant\|wpa_cli\|dhclient\|ifplugd\|dhcdbd\|dhcpcd\|udhcpc\|NetworkManager\|knetworkmanager\|avahi-a PHY Interface Driver Chipset phy0 wlan0 ath9k Not pci, usb, or sdio phy0 wlan0-1 ath9k Not pci, usb, or sdio phy1 wlan1mon rtl8192cu Realtek Semiconductor Corp. RTL8188CUS 802.11n WLAN Adapter phy2 wlan2 ath9k_htc Atheros Communications, Inc. AR9271 802.11n root@Pineapple:~# root@Pineapple:~# pinesniffer wlan1mon 60 0 /tmp/test [*] Pinesniffer started on wlan1mon, running for 60 seconds [*] Scan results written to /tmp/test root@Pineapple:~# cat /tmp/test {"ap_list":[], "unassociated_clients":[]}root@Pineapple:~#
  3. logs are not immediately exportable, but I see nothing of note other then this: Sun Mar 19 21:25:49 2017 cron.err crond[1397]: time disparity of 1391 minutes detected Sun Mar 19 21:26:40 2017 kern.info kernel: [ 1196.560000] rtl8192cu: MAC auto ON okay! Sun Mar 19 21:26:40 2017 kern.info kernel: [ 1196.590000] rtl8192cu: Tx queue select: 0x05 Sun Mar 19 21:34:29 2017 kern.err kernel: [ 1665.550000] rtl_usb: reg 0xa2c, usbctrl_vendorreq TimeOut! status:0xffffff6f value=0x6010840 Sun Mar 19 21:34:39 2017 kern.err kernel: [ 1675.550000] rtl_usb: reg 0x608, usbctrl_vendorreq TimeOut! status:0xffffff6f value=0x17130e09 Sun Mar 19 21:34:49 2017 kern.err kernel: [ 1685.550000] rtl_usb: reg 0x608, usbctrl_vendorreq TimeOut! status:0xffffff6f value=0xf7900f0 Sun Mar 19 21:34:59 2017 kern.err kernel: [ 1695.550000] rtl_usb: reg 0xda0, usbctrl_vendorreq TimeOut! status:0xffffff6f value=0x1f5c8a1d I think that this may be a browser issue as I can scan if I kill the browser and log back in. Still seems awfully touchy though, is this normal?
  4. Thanks b0N3z, sounds like I should have looked closer at the logging page. I will post as soon as I can get back out to the office but how do you guys tag logs to keep from filling up the whole topic ?
  5. I would if I could find logs on it... as per above, /var/log is empty and the logging page is all about PineAP
  6. Left it alone overnight, tried again this afternoon. Now I can get a scan going but the results make no sense... Ran for 15 second scan, after a few seconds the bar expanded for 20 seconds, hung at 100% for several minutes. then stops, still showing "No scan results." Meanwhile, from the command line I do see SSIDs... root@Pineapple:~# iwlist wlan0 scan | grep SSID ESSID:"Scott's Wi-Fi Network" ESSID:"Helgen_2GEXT" ESSID:"Helgen" ESSID:"gwguest" ESSID:"DVW326.9D1105-2.4G" root@Pineapple:~# iwlist wlan2 scan | grep SSID ESSID:"" ESSID:"Helgen_2GEXT" ESSID:"Backup" ESSID:"gwguest" root@Pineapple:~# iwlist wlan0-1 scan | grep SSID ESSID:"Scott's Wi-Fi Network" ESSID:"Helgen_2GEXT" ESSID:"Helgen" ESSID:"gwguest" ESSID:"DVW326.9D1105-2.4G" Swapped out antennae for the original ones, no improvement. Swapped out the SD card for a different, formatted one, no improvement. Rebooted with no SD card, no improvement. So I bought this in August and still have yet to get it to work correctly... is there any way to replace it?
  7. OK... so I thought I would give the Nano a few months, see what firmware came out, and try again. Just flashed with [Release] 1.1.3 - Codename Buffalo Bulldozer and uninstalled all modules, then rebooted. From the Dashboard I click Recon, select "30 Seconds" and hit the "Scan" button. The little pineapple icon animates but the scan never starts. two minutes later I refresh the browser and briefly see a red warning "There was an error starting Recon, please try again" At this point the Dashboard stops working (UPTIME and % CPU USAGE are blank) and the left-hand nav bar stops working, no pages will load. So, I have been trying to get this working since DefCon and feel like this is as vanilla as I can make it... am I doing something wrong? Is there a way to RMA the hardware? Are their logs I can check (/var/log has nothing but lastlog and wtmp) note: ssh-ed in and still able to move around while the web interface is locked... the actual Nano does not seem to have frozen up, just starting Recon breaks all web interfaces... note: found the "Download debug" button on the Help page, result is a blank page simply stating: "Invalid file." Closest thing I can find to logfiles is dmesg, this is what i see after starting Recon: [ 403.530000] rtl_usb: reg 0x603, usbctrl_vendorreq TimeOut! status:0xffffff6f value=0x4040501 [ 403.790000] rtl_usb: reg 0x608, usbctrl_vendorreq TimeOut! status:0xffffff6f value=0x2e9003 [ 413.530000] rtl_usb: reg 0x442, usbctrl_vendorreq TimeOut! status:0xffffff6f value=0x483 [ 413.790000] rtl_usb: reg 0xda0, usbctrl_vendorreq TimeOut! status:0xffffff6f value=0x0
  8. OK... so I removed all from my SSID list and manually entered abc_fake and xyz_fake. Fired up PineAP Daemon: Enabled PineAP -> Broadcast SSID Pool Broadcast SSID Pool interval -> Aggressive started up a tablet and it see neither as available, but it automatically connected to one of the fake SSID's I made last time that is no longer being broadcast or on the list. Manually entered abc_fake into the tablet and it connected. Entered SSID "noodle" on the tablet as I have never used this before, tablet connected. So This works like the MkV where it quietly claims to be whomever you are asking for, but then why do I need to broadcast SSIDs if I cannot see them and the clients just join whatever i ask to join as the Pineapple?
  9. not to bump my own post, but as I see no SSIDs other than the real ones I am asking again... should I see my whole list of 144 SSIDs from the PineAP SSID list when I broadcast SSID Pool? Phones and PCs see none of the fake ones but I could swear i saw them all in iwlist when I was on the previous version
  10. waited a while and tried cold, full plug in. dmesg -T from laptop: [Wed Aug 31 22:36:50 2016] usb 3-1: new high-speed USB device number 9 using xhci_hcd [Wed Aug 31 22:36:50 2016] usb 3-1: New USB device found, idVendor=0b95, idProduct=772a [Wed Aug 31 22:36:50 2016] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [Wed Aug 31 22:36:50 2016] usb 3-1: Product: AX88x72A [Wed Aug 31 22:36:50 2016] usb 3-1: Manufacturer: ASIX Elec. Corp. [Wed Aug 31 22:36:50 2016] usb 3-1: SerialNumber: 90D1F9 [Wed Aug 31 22:36:51 2016] asix 3-1:1.0 eth1: register 'asix' at usb-0000:02:00.0-1, ASIX AX88772 USB 2.0 Ethernet, 00:c0:ca:90:d1:f9 [Wed Aug 31 22:36:52 2016] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [Wed Aug 31 22:36:52 2016] asix 3-1:1.0 eth1: link down [Wed Aug 31 22:36:52 2016] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [Wed Aug 31 22:36:53 2016] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [Wed Aug 31 22:36:53 2016] asix 3-1:1.0 eth1: link up, 100Mbps, full-duplex, lpa 0x4DE1 [Wed Aug 31 22:37:21 2016] asix 3-1:1.0 eth1: link up, 100Mbps, full-duplex, lpa 0x4DE1 dmesg from pineapple:
  11. Does not connect... dmesg on the laptop (not pineapple) is: [ 193784.536658] usb 3-1: USB disconnect, device number 7 [193784.537507] asix 3-1:1.0 eth1: unregister 'asix' usb-0000:02:00.0-1, ASIX AX88772 USB 2.0 Ethernet [193802.506634] usb 3-1: new high-speed USB device number 8 using xhci_hcd [193802.654381] usb 3-1: New USB device found, idVendor=0b95, idProduct=772a [193802.654392] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [193802.654398] usb 3-1: Product: AX88x72A [193802.654403] usb 3-1: Manufacturer: ASIX Elec. Corp. [193802.654407] usb 3-1: SerialNumber: 90D1F9 [193803.458523] asix 3-1:1.0 eth1: register 'asix' at usb-0000:02:00.0-1, ASIX AX88772 USB 2.0 Ethernet, 00:c0:ca:90:d1:f9 [193804.567154] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [193804.570411] asix 3-1:1.0 eth1: link down [193804.573993] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [193805.059705] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [193805.062239] asix 3-1:1.0 eth1: link up, 100Mbps, full-duplex, lpa 0x4DE1
  12. Sorry, but dumb question... when I have PineAP broadcasting the SSID pool I should be able to see the fake SSIDs from another machine running "iwlist wlan0 scan" when the PineAP Daemon is enabled and "Broadcast SSID Pool" is checked and saved right? I thought I saw that with the previous version but now under 1.1.1 I am not sure I am broadcasting as I only see the real ones (on real Channel 11 as opposed to Channel 1 where I have the Pineapple Access Point Channel set).
  13. Understood. My concern was that if I have it out and not in the case it is difficult to handle (plug in, unplug, fondle, etc) without touching the antennae. As a total newb, was unter the impression that touching a powered antenna would have some profoundly adverse effect. If this is correct I would leave them off until I re-case it. If this is wrong and you tell me I am a Trottel I will put them back on :)
  14. Totally worked, thanks. If anybody cares, I put both copies in the same local directory, renamed ssid_file_one and ssid_file_two touch NEW_ssid_file cat ssid_file_one >> NEW_ssid_file cat ssid_file_two >> NEW_ssid_file sort NEW_ssid_file | uniq >> ssid_file scp ssid_file root@172.16.42.1:/etc/pineapple/. good to go! Now seeing 144 SSIDs in pool
  15. Heh... new record for attaching on the first try, of course. I will post as soon as I see it again :)
  16. oh man, why did I not think to ssh in and vi the file... that is by far a better idea than trying to overwrite in the web client. You shame me with the simple solution I should have come up with on my own. Thank you... I need to think more before I post :)
  17. Can you import ssid_file files like those created when you select PineAP => SSID Pool => Download SSID Pool? Is it actually a binary? The browser claimed it was .bin, but I can egrep and tail it like a text file and it saved with no extension. I have had to rebuild a couple times and a would love to merge by disparate files into a master list. I have a Pineapple Nano running firmware 1.1.1.
  18. I have been dealing with an oddity, wonder if anybody has seen similar and has suggestions. I have a Pineapple Nano running firmware 1.1.1. When I connect the USB y-cables to the Nano and a laptop running Ubuntu 16.04 LTS, about half the time I see an IPv6 address assigned but never IPv4 and have to unplug, cool, then try again. Same issue on a Raspberry Pi 3 running Kali. (Yes, I went there.) Example: user@***-Ubuntu:~$ ifconfig eth1 eth1 Link encap:Ethernet HWaddr 00:c0:ca:90:d1:f9 inet6 addr: fe80::5851:89df:4911:ae3c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:58 errors:0 dropped:0 overruns:0 frame:0 TX packets:94 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2668 (2.6 KB) TX bytes:15606 (15.6 KB) It seems like if I then disconnect, wait a few seconds and reconnect, it goes through the second or third try: eth1 Link encap:Ethernet HWaddr 00:c0:ca:90:d1:f9 inet addr:172.16.42.42 Bcast:172.16.42.255 Mask:255.255.255.0 inet6 addr: fe80::be0f:d824:b0c0:2e77/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1022 errors:0 dropped:0 overruns:0 frame:0 TX packets:1074 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:601481 (601.4 KB) TX bytes:256879 (256.8 KB) (realized this was in a thread on wlan0 issue, deleted there and moved here)
  19. not even kidding.. I have made this mistake so many times :) If you get short micro USB cables bundled to charge something do check them before you do like I did and spend several days trying to understand why a Raspberry could not talk to an Arduino over USB :)
  20. Fallen Archangel, were you able to get it working by installing Kismet and using the "USB Mouse Receiver"? Any particular resource you found helpful?
  21. I noticed the same thing at DefCon when just collecting SSIDs with PineAP. I was told by the folks at the vendor booth (and I want to say later confirmed on these forums) that it gets hot but that is normal... not something to worry about. That being said, if you see a headline about an old man in AZ spontaneously combusting while WarDriving (well, WarDogWalking...) please disregard my assurances of safety
  22. You may need to reset the "Save active config as default" on the Configuration tab... once I did that again it was back to working.
×
×
  • Create New...