viperius

Just done a reboot after removing the swap partition Filesystem Size Used Available Use% Mounted on /dev/root 13.0M 13.0M 0 100% /rom tmpfs 29.1M 164.0K 28.9M 1% /tmp /dev/mtdblock3 1.3M 400.0K 880.0K 31% /overlay overlayfs:/overlay 1.3M 400.0K 880.0K 31% / tmpfs 512.0K 0 512.0K 0% /dev /dev/sdcard/sd1 3.6G 32.0K 3.6G 0% /sd sd card seems to be there I am going to try and install some stuff and see what happens

Things just got weirder. When I booted up the NANO and looked in the resources and I can see the SD card.... I went to modules and tried to install something onto it and I didn't get the install option and when I go back to resources the SD card is no longer there.

config 'global' option anon_swap '0' option anon_mount '0' option auto_swap '1' option auto_mount '1' option delay_root '5' option check_fs '0' config 'mount' option target '/sd' option device '/dev/sdcard/sda1' option fstype 'ext4' option options 'rw,sync' option enabled '1' config 'swap' option device '/dev/sdcard/sda2' option enabled '1'

I cant see anything obvious. Maybe its time for an upgrade.

That looks fine....formatted ext4 and when I look on my raspberry PI it is mounted as /dev/sdc and I can see it in the file manager so I would say all looks good but its still ne showing up on the nano.....

Hi there everyone, its been a while since I used my NANO and I have had a few challenges getting it working. The main one I am having problems with is getting the NANO to recognise and initialise an SD card. Using Firmware 2.7.0 I have a 8gb SD card I put in the NANO and boot. if I go into the UI then I can format the SD card but it does not show up. I have tried a couple of SD cards in different sizes and I have also deleted any existing partitions before starting. I am open to any suggestions Thanks

Ok some more info. I have setup the Mk IV as a Wi-Fi hotspot and connected to it using my mobile phone. I can then browse on my phone so there is obviously a connection from the MKIV through the notebook an out to the internet. So the question is.....why is it still telling me no connection when I try and get to the pineapple Bar, upgrade or reveal public ip. Have I missed something? or are the MkIV servers no longer functioning.

Further info... I can ping www.wifipineapple.com and cloud.wifipineapple.com from within the advanced tab

Greetings one and all. I have a Mark iV and it was working a while ago and I have just got it back out and now it is not behaving. A few things may have changed in the ensuing time (new versions of Linux, windows etc) a new broadband provider and I am a bit older and some of the brain cells may have died. So I have followed the instructions in the book and have the following set up Linux - ububtu 14.04 LTS running 32bit (this is a small note book machine) mk IV is running 2.8.1 firm ware I have a verbatim 16GB USB drive (with 2 partitions) I have run wp4.sh wifi adaptor (wlan0) on notebook is connected to home network and I can connect to internet via browser Ethernet (eth0) is setup as 172.16.42.42 to communicate with mk IV MK iV is 172.16.42.1 and I can connect to it via the browser using 172.16.42.1:1471 )I have a cat5 cable plugged into the POE/LAN port) All was seeming good at this point. Now the fun stuff starts. When I click reveal public ip I get "Error Connecting" When I click check for update I get "Error Connecting. Please make sure you have a working connection!" When I try and get a list of infusions I get the same error. Things I have tried I did a factory reset of the MK iV I tried connecting the MKIV to my network via the Lan Port I tried tethering it a windows laptop running windows 10 following the instruction in the book and guidance from the internet (got the same results) Like I said I had this working before but I am obviously not doing something. Any help/suggestions would be greatly appreciated.