HammerHead_0718

I've made too many replies and at this point I should probably just address everyone... but thank you anyway for your suggestions. I think I am going to go with the Yagi. Decent price too and it will work with both the tetra and the Nano with or without adapters if I am correct. Once again, Thanks.

I certainly am looking to get the Yagi antenna at this point. 30º beam width is fairly narrow and I like that.

The size is a bit of a factor. I don't mind the Yagi antennas but prefer either that size or smaller. The narrower the beam-width the better. I don't need it to have a crazy gain either. Thanks for your help. All of theses suggestions are great. I just need to narrow it down. No pun intended.

I will likely use it with the nano if I do get it. Thank you for your help.

Thanks. I don't care so much about distance but rather direction. Trying to pinpoint the locations of rogue APs across a large business campus. so the more directional the better.

Not sure if this belongs here but I'll ask anyway since it's firmware related. How difficult would it be to incorporate a sorting for the table headers in recon? For example lets say I wanted to sort highest to lowest in signal strength. RSSI or I wanted to sort it by mac address AA before BB. Is this something I can do myself within the system's files without violating any of Hak5's terms of use? Thanks for all the hard work. Great release BTW.

I'm not looking for long rage per se, but are there any Highly directional antennas to pinpoint APs? Like rouge detecting by pointing at a building or cubicles. Does anyone have any recommendations?

Hi Seb, thanks for the input. but just to verify... you physically have to push the reset button? Also, any plans to add python support for modules?

I left my WPT powered and connected via ethernet in my home network and I am now traveling for work. I noticed I haven't updated the firmware in a while and is pending. without having physical access at the moment, can I remotely update the firmware without having to push the button reset button?

I know a few years ago there was a question regarding hacking ISO-7816 contact cards. Well I'm here to ask a few questions. I would like to know if anyone here has any experience with Smart Cards and providing some guidance to learn to read the card. So far I have search the internet and found plenty of information about the smart card. however, I cannot seem to find anything that would either show me how to access the card with a card reader ( without making your own software) or what I need to do to make the software. Most of the software programs are pre 2010 and have no support or are extremely outdated. I have tried smart card toolset pro, exeba comm, atmel crypto, skycard, and a whole bunch of other software that usually come up with similar errors like unable to access card due to sharing violation... other connections outstanding... If anyone has any advice feel free to comment. Also, I have gone through a bunch of Hackaday and other hack forums that also predate quite a bit. Some were very informative but not enough to accomplish my goal.

I'm getting more and more familiar with airodump-ng but noticed there is also TCPDump. I have a few questions. Am I correct to assume that airodump-ng is solely for wireless sniffing while tcpdump is any interface including wired connections? if that is so... will running tcpdump on my wireless interface card while it's in monitor mode, shouldn't it pick up 4 way handshakes (WPA2)? Thanks.

Thanks Seb. That's exactly the answer I was looking for. Cheers!

Are there any plans to port the module over for the Tetra/Nano? I'm asking for a friend.

Can't seem to install dependancies. I'll download the modules and install them on the SD card, then install the dependencies on the SD as well. I've tried factory reset and installing them again, but it doesn't work. Any ideas? Thanks.

Did you try the DEFAULTDELAY command with the GUI SPACE.

Also be sure to add DEFAULTDELAY or DEFAULT_DELAY at the beginning of the script for Mac and Linux os' DEFAULTDELAY 750

Substitute COMMAND with GUI that should do the job

I wish that were true but it's not. I went to great lengths to ensure that the payload I encoded was the right inject.bin file transferred to the ducky. I erased and emptied the trash bin as well as formatted the sdcard. I know it's the right inject.bin because when I decode it it has the right script.

How about an analyzer that does 2.4 and 5.0?

Hi everyone, Seems as though my previous script has somehow embedded itself in the ducky. For example, I'll write my script, encode it and then copy it to a formatted SD card. I'll pull the SD card from the drive and place it into the duck. From there I place the duck into my usb drive and wait for the script to execute. This is where things don't make sense. My previous script was a simple notepad string output with two string lines. It worked flawlessly. However, my new script is a bit more advanced and should include things like command line. However, the script executing is my notepad script and not my new one. Does anyone have any idea? I don't want to reflash my ducky again but I will if I have to. I would also like to UNDERSTAND why this happened. I'm using twin duck firmware (just basic) on a brand new Rubber Ducky.

Thanks for your help. I have started and figured out many awesome things you can do just by using the keyboard.

Hello Rubber ducky forumn, I've been mostly active on the WiFi pineapple side of this community and have just received my RD. I'm not one to just start asking for people to do things for me.... But I do have a few questions. First off, I'm not sure what I need to start using RD. Do I need an encoder? If so, I've only seen a linux based encoder. Is there one for windows? I'm sure I use my MBP for that as well. My primary machine is a windows 8.1 laptop and I have Kali linux as well as a MacBook Pro. I'd like to use my windows computer since thats what I work with on the go. Second, is there a detailed guide on keyboard commands that are not as common to most users for windows, mac os x, and gui based linux OS? I have also seen the repository for scripts made by others so I know that's there, but I'm looking for instructional articles/videos to learn how to make my own. I'm sorry if this comes off as extremely simple, but I would rather hear what the community has to say rather than assuming anything. Thanks!

did you try formatting the sd card from the configure menu on the pineapple?

You wouldn't do it... It's just a cry for help.

I will definitely have to work on making it happen. Thanks for the info!