846846
-
Posts
19 -
Joined
-
Last visited
Posts posted by 846846
-
-
We're sorry. You can't access this item because it is in violation of our Terms of Service. :(
-
Hi Sebkinne,
firmware recovery worked fine, thanks... stupid I didn't' think about it myself....
Where can I post these (stupid) questions next time, it's not clear to me where...
Thanks...
-
Hi,
after upgrading to 1.1.2. the nano does not work anymore. If I plug in the nano, the blue light is on for two seconds, then you light goes out. The WP6 does not recognise the nano via the [C]onnect using saved settings. tried the option [G]uided setup: he detects the Nano in step 3 but after saving and starting via option C Linux can't detect it anymore.
Holding the reset button and plugging it in, the light stays blue but is not blinking. [C] does not work, and when you try [G]uided setup, you have to reconnect the Nano in step three and the light goes out after 2 seconds again. Holding on the reset button in step 3 the light stays on but after saving settings and start with [C], WP6 does not detect the Nano.
Never had problems before, started when starting after upgrade 1.1.2.
Step 1 of 3: Select Default Gateway
Default gateway reported as 172.16.160.2
Use the above reported default gateway? [Y/n]? y
Step 2 of 3: Select Internet Interface
Internet interface reported as eth0
Use the above reported Internet interface? [Y/n]? y
Step 3 of 3: Select WiFi Pineapple Interface
Please connect the WiFi Pineapple to this computer.
...........[Checking]
Detected WiFi Pineapple on interface eth1
Use the above detected WiFi Pineapple interface? [Y/n]? y
Settings saved.
Saved Settings: Share Internet connection from eth0
to WiFi Pineapple at eth1 through default gateway 172.16.160.2
[C]onnect using saved settings
[G]uided setup (recommended)
[M]anual setup
[A]dvanced IP settings
[Q]uit
Detecting WiFi Pineapple.................................................................................................................................................................................................... -
I had no problem, didn't have to pay import taxes or whatever...
have fun with it... :)
-
Kali 2.0 VM on a MacBookPro (2013)
-
Have you tried doing a factory reset? See https://forums.hak5.org/index.php?/topic/37210-just-bricked-my-nano-howto-unbrick/
Factory reset was the trick. Thanks
- 1
-
Hi, I think the filesystem is full cause
Can't clear SSID Pool, I can clear but after refresh the list is not gone;
I can't remove Modules, he says he does but after plug off/in they not really gone.
I can't save PineAP Settings as a config default.Filesystem Size Used Available Use% Mounted on
rootfs 2.3M 2.2M 52.0K 98% /
/dev/root 12.5M 12.5M 0 100% /rom
tmpfs 29.9M 100.0K 29.8M 0% /tmp
/dev/mtdblock3 2.3M 2.2M 52.0K 98% /overlay
overlayfs:/overlay 2.3M 2.2M 52.0K 98% /
tmpfs 512.0K 0 512.0K 0% /devWhat's the best way to resolve this and if it's the filesystem, what's the best way to clean it up?
-
Use the Bug Tracker.
Hi Foxtrot, already did...
problem solved... you have to refresh the page after checking the boxes...
-
I upgraded to 1.0.3.
Wasn't Modules to be enabled since 1.0.2?
Also, when I try to enable PineAP daemon, it gets de-selected upon hitting the save button.
The last problem I already had with 1.0.2.... created a ticket for that...
@Sebkinne and @Darren, what's the best way to report 'bugs'? via Forum or Ticket?
Mr Robot Hack
in Classic USB Rubber Ducky
Posted
Hello Enzym3, link works fine now... thanks