Jump to content

haroo

Active Members
  • Posts

    50
  • Joined

  • Last visited

Everything posted by haroo

  1. i have a raspberry pi that connects to the internet and shares it to my pineapple via Ethernet (the RPI is setup right and works awesome at boot) but when i boot the pineapple i need to go to network and add the br-lan route for the tethering to work. this is a permanent setup and i want that route to be set at boot. i have looked and i know this is an easy one but i am just stumped... any help would be awesome.
  2. I got it, what i did. formatted SD card ext4 primary (was ext4 before but was logical) dip 5 down ,no sdcard, boot http://192.168.1.1 uploaded factory file. got the good light sequence right away after it finished. put sdcard in flipped up dip 5 restarted. off to the races.
  3. i found a 12v 1A power supply and im trying it right now to completely rule out power issue
  4. OK, I'm pretty experienced with the wifi pineapple and Linux in general I'm no expert but i can get around and do what i need to do. that said. i recently pulled my MKV out and dusted it off. I had stole the sdcard for another project at some point. i booted the mkv up and all i got was solid green and flashing blue light. i let it flash blue all night and same thing in the morning. i rebooted. same. i found a 2gb sdcard, i formatted it FAT put it in the MKV, put dip #5 down and booted up hooked to my PC with an ip address of 192.168.1.2. i http://192.168.1.1and get the recovery page. i downloaded the proper factory bin and it went too 100% and told me to flip my dip back up and reboot, so i did.. reboots to blinking blue. things i have tried -format the sdcard EXT4- still blinks blue for hours after the reboot -let it sit after loading the bin for it to get the happy light sequence - still blinks blue forever. - tried to power off my batt - still blinks blue for days - tried a different power supply 9v 1A = 9 watts should be good right? - tried an 8gb class10 sdcard - same after changing each variable i followed the unbrick process with no success. i have read a similar thread on the same issue and the admin said the answer was in the FAQ. if it is i'm blind or retarded. Thanks for the help Haroo
  5. there is an infusion for this it makes it easy. its called network manager. for fw 3 its called wifi manager but i couldnt get wifi manager to work so i downgraded to 2.8.1 and i was up and running in a few min. hope this helps and makes it easy for you. haroo
  6. im using 12v 1A. could i go bigger than that safely? i dont have the serial device to reflash but will order one when i can. Thanks
  7. ok so my pineapple reboots when i have it under a little load. i have checked everything i can find on the forums i think it has to do with this /dev/root 5.3M 5.3M 0 100% /rom when i first got my pineapple i installed some infusions to the device and that seemed to have filled the dev/root/ does anyone know where i can find some files i can delete to free up some room to see if thats my issue? Im on FW 3 but was having the same issue on all the other revs Thanks Haroo
  8. i have reverted to 2.5.0 and so far i have not got a reboot and im up for 30 min now. will post results. if its works good ill go back to 2.7.7 and see if i get reboots
  9. runs longer without reaver. last time it rebooted it didnt recognize the ath9k i unplugged it from the hub and plugged it back in and it recognized it .
  10. when i just run sslstrip and no reaver it does the same thing but lasts longer than when i have reaver running
  11. /dev/root is completely full and i dont know why that is. is there a way i can clean it up?
  12. root@Pineapple:~# free total used free shared buffers Mem: 29336 28380 956 0 1648 -/+ buffers: 26732 2604 Swap: 975748 6168 969580 root@Pineapple:~# ps root@Pineapple:~# df -h Filesystem Size Used Available Use% Mounted on rootfs 1.1M 444.0K 644.0K 41% / /dev/root 5.0M 5.0M 0 100% /rom tmpfs 14.3M 120.0K 14.2M 1% /tmp tmpfs 512.0K 0 512.0K 0% /dev /dev/mtdblock3 1.1M 444.0K 644.0K 41% /overlay overlayfs:/overlay 1.1M 444.0K 644.0K 41% / /dev/sda1 2.8G 142.8M 2.5G 5% /usb
  13. sorry it took me so long to reply. i have been running on wall power. i have tried with usb all unplugged. though it defeats my purpose. i have my powered usb hub also plugged into wall power. on the hub i have my flash drive and my alfa radio. any more suggestions would be awesome.
  14. ok just wondering if guys are having this issue. its rebooting every hour on the dot. im powering off of usb on my laptop and running 2.7.7 HAROO
  15. will do when i have a chance. it was a fresh flash. but ill try it again. i have to go to 2.7.7 anyway
  16. I will take a look at the model for you when i have a chance. i power my hub via usb off of a usb port from my batt back. as far as i know most / all usb hubs will be 5V 1-2A as native usb power is 5V. when you get a new one take a look at what voltage it requires. it should say on the package or on the bottom of the usb hub. as for my cable to power it. i was going to cut a usb cable and the end off my ac adaptor that came with them and home brew that with a soldering iron and some heat shrink but i was lucky and had a power cable from a blutooth headset i had that was the same size barrel connector on one end and usb on the other so i didnt have to frankenstein anything to make it work. most barrel power connectors are pos in the centre and neg on the outside but some devices are ass backwards to take a look. you can confirm your polairity with a multimeter useing a simple conductivity test. should be centre to center and outside to outside in your case. i think overvoltage is what cooked your usb hub if you were feeding it 9-12Vdc how did the new FW help you? Haroo
  17. i just updated to 2.7.6 and installed network manager. when i go to use it i dont get any of the options. it loads the line with [Auto-Detect] [Save] [Commit] [Revert] and nothing below it. any ideas? Haroo
  18. yup it was my fire wall. Thanks for the help guys. This is an awesome community and i am very grateful for all the help.. Haroo
  19. ok windows issue was AVG firewall blocking it. got it now. its strange that it was working before and then all of a sudden stopped. im starting to question my AVG internet security business / corporate edition as it should have never let it work instead of letting it work then not. if it was something malicious then it would have allowed it for a bit lol Thanks for all the help!
  20. thanks for the suggestion BTW its appreciated
  21. i dries both of those suggestions already and no go for me. still haven't tried a different ubuntu distro yet. still downloading. im on a slow satellite connection at work right now.
×
×
  • Create New...