Jump to content


Active Members
  • Posts

  • Joined

  • Last visited

  • Days Won


Everything posted by Geoff0ne

  1. I would but i cannot view your topics under your profile.....
  2. Correct me if im wrong, but the evil portal only realistically can produce a single phishing page being the landing page. Is this right?
  3. OK Total noob here. What i was doing is a dd of the image to the partition itself (disk4s1) and not the disk (disk4).
  4. This? https://mitmproxy.org Looks fairly simply to configure.
  5. Im bringing this thread back to life as I've encounted the same problems again with the current kali 1.0.9 raspberry pi build. https://www.kali.org/news/kali-tools-website-launched-1-0-9-released/ It simply won't boot, the red and green lights on the pi remain static and there is not display output. I have tried: Replacing the bootcode.bin and start.elf, start_cd.elf, start_x.elf files which previously worked as per here http://raspberrypi.stackexchange.com/questions/22573/failing-to-boot-kali-on-b-model-pi - no go. Reformatting the SD card numerous times with different methods. Installing NOOBS (basic rasp pi image) to rule out the fact of a dodgy SD card / rasp pi. - Boots fine. Ive tried installing the image using root@kali:~ dd if=kali-pi.img of=/dev/sdb bs=512k - copies files across but still not booting. Ive tried installing the image by simply copying and pasting the contents of the img file to the Sd card - confirmed files copied across but still not booting. Any ideas?
  6. You're waisting your time with DNSpoof. The spoof success rate is fairly low given most modern browsers cache the correct DNS entries.
  7. Figured it out. Its a bug in WICD network manager, even if its connected to a wired and wireless interface, it will only actaully display as being connected to a single interface.
  8. Hello. This is my basic setup. Raspberry Pi B+ running Kali connected to: 1. Home router on from wlan2 2. Pineapple via eth0 I'm able to run the wp5.sh script from within kali just fine. Looking at WICD network manager, it wont allow both the wired and wireless interfaces to connect at the same time. Any workaround?
  9. What sort of throughput speeds are you getting with AWUS036NEH setup in client mode?
  10. Hi Guys, I went out and purchased the AWUS036NEH. I'm still not entirely convinced the AWUS036NEH solves the problem. Here's what i did. Setup a hotspot on my Android Galaxy S3 broadcasting on channel 1. Connected directly to Android hotspot from desktop PC with these results: I then immediately ran the same speed test, again from my desktop PC which is now connected to my pineapple over the air and configured in client mode to connect to the Android hotspot. Note: pineapple SSID is broadcasting on channel 6 and the hotspot is still running on channel 1. What am i doing wrong?
  11. new image works well. keyboard and mouse support
  12. tested pwnpi. Boots fine with replacing the files on the boot dir as per this https://gist.github.com/MikeyJck/e0baf8977dfbf2c2fd67 Keyboard works fine.
  13. Yeah im having the same issue. wired and wireless keyboard wont work but i can see they are detected when booting. Tried a powered USB hub and changed the power adaptor to the pi still no win.
  14. My plans are to basically replicate the pineapple as much as possible and make it a more reliable alternative.
  15. Followed this guide here to burn the image to a microSD http://www.r00tsec.com/2013/04/howto-installing-kali-in-raspberry-pi.html Powered on raspberry connected to monitor via HDMI. Not picture on monitor. The red and green lights on the Pi remain on. Tested on Kali Pi images 1.0.6 and 1.0.7 no go.
  16. Whats the best way to stay informed of when they release a new build?
  17. Yes. Tested another Distro on two seperate micro SD cards - booted fine. I was hoping not to wait for another build.
  18. Hola, Has anyone successfully installed Kali on the new B+ raspberry and please advise how you did it? Im not 100% but i think the current Kali raspberry pi image doesnt work with the B+ after imaging from various OS's to the microSD for the raspberry. I would ask on Kalis forums, but they dont approve new postings.
  19. Make sure to check your local laws before getting one. The allowable output varies from country. If not careful you can cause alot of interference with other wifi networks in your area.
  20. *following* keen to know if this is more effective than dnsspoof
  21. Ive been waiting for a solution to this for over 6 months. With manufacturor restrictions getting tighter and still no current hack/workaround. Don't hold your breath, go buy an amp. http://www.amazon.com/Signal-Booster-Amplifier-Wireless-Antenna/dp/B00CR6V0GS/ref=sr_1_22?ie=UTF8&qid=1406816232&sr=8-22&keywords=wifi+amplifier
  22. Still issues with installation. Tested with multiple browsers. Firefox from android phone - no go Iceweasel from desktop pc - no go firefox from macbook - no go safari from macbook - WORKS !? OMFG
  23. Koolkarnt, ive followed your steps with little success. 1: connected to PA via broadcasted ssid - login to port 1471 2: start wlan1 - client mode - connect to hotspot 3: installed infusions wifi manger,ettercap urlsnarf and dnsspoof 4: enabled ICS from wlan1 to wlan0 in wifi manager 5: tested networking, can access sites and such. - next step 6: ettercap -i br-lan -M arp:oneway,remote // // 7: Urlsnarf and dnsspoof running on br-lan 8: Test from a client machine connected to broadcasted SSID from wlan0 - no internet 9. Test from client machine connected directly to hotspot that wlan1 is connected to in client mode - no internet from client machine. wrong ettercap command? I have also tried running ettercap on the wlan1 interface - with the same outcome as step 8 & 9. edit: Tried disabling wlan1 and setting up a USB alfa to connect in client mode the hotspot on wlan2. Then do a ettercap -i wlan2 -M arp:oneway,remote // // Still no go - both directly connected client machines to wlan0 AP and exisiting clients on network attached to wlan2 in client mode - no internet.
  24. Guys I'm having a bit of trouble getting this to run. It always comes up with "ettercap is not running..." after executing various commands. This is my current setup. wlan1 is connected to network in client mode with DHCP address of I want to ARP poison which is on the client network. The gateway on the client network is The pineapple is running on the default network. Can someone please confirm the correct settings / command to ARP traffic from a client on the client network. Or is it simply not possible to ARP clients on the network configured as client mode? thanks
  • Create New...