BigFanOHak5

You should be able to exchange it for another if it is brand new. The Hak5 customer service is great.

"Setting up ICS" means Internet connection sharing through your OS (ie Windows, Mac, Linux). As for the usb-uart adapter I use, I bought it off Ebay. It took about a week in a half to arrive because it was coming from China, but I can vouch that it works. Here is the link: http://www.ebay.com/itm/370532286388?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649

Have you tried removing the flash stick from the usb and then booting? Also (if not already) use the wall wart to power the pineapple instead of the portable battery. If all else fails, do a clean flash. You can open it by removing the two screws under the rubber feet. It should be on the side where the usb is at. Get the USB to UART cable but make sure it has 3.3v.

Awesome thanks for all the hard work. Will this release allow for iphone tethering?

I reflashed it again with v2.3.1 and it works now. Not sure why or what changed. Maybe the first time was a bad flash? Doesn't make any sense, but I'm glad to get it working again.

The wlan light is constantly flashing. It happens when any device connects to the pineapple mark iv. Once the device is connected, it will not allow the connected device to load any webpages. This started when I followed petertfm's how-to guide for random rolling. I followed the guide to a "T" and all seemed to work fine. The rolled pages were working great and randomizing as it should, but as soon as I turned off dns spoofing is when the wlan light flashing stayed constant. I have tried to reset, reboot via web ui, unplugging power adapter, upgrading, and even did a clean flash with no success. Seems to me like it may be a hardware issue? Nothing I try works. I am able to view the web ui and ssh in as normal. help.

Thanks for this. It works like a charm. Only question I had: When I disable dns spoof, it doesn't go back to normal webpages- any page I to go to times out. Do you think the pineapple has to be rebooted every time to go back to normal? I've tried to clear the cache on the pineapple. I also noticed the Wlan light blinking constantly as if it was still reading one of the roll pages.

I ask because it seems like whenever I just unplug the power from my pineapple, the next time I boot it up it doesn't let me log into the webui. It isn't until I reflash the firmware when I can get back in again. Everything is stock, I have no modules installed at this time.

Followed your guide, but when I get to this step: iptables -t nat -A PREROUTING -p tcp --destination-port 80 -j REDIRECT --to-ports 10000 It booted me from the webui and now when I try to get back to the webui, I get problem loading page error. thoughts?

I'm a bit confused on the sslstrip module. If I install it via the pineapple bar, do I need to do anything else or does the module auto installs all the things needed to make it work? I keep seeing threads popping up about fixing ip tables and such. Just want to know before I install it via pineapple bar. thanks

Lol, i fast-forwarded past some of the video and missed that step. All sorted now. Thanks for helping petertfm.

I pulled out my old 32-bit windows vista laptop. I got it to work there, but I'm at the part where I need to log into via winscp. The video shows that its is a four letter password. I tried "toor" and "pineapplesareyummy" What's the pass? thanks

Tried in administrator - no go. I even tried it on my other 64-bit windows 7 laptop and no such luck as well. The only difference is I don't get the error on that laptop. When I start Tftpd64 the server interface shows 192.168.2.11. Not sure what else it could be.

When I try to start Tftpd, I get the error message listed below. I am trying to do a clean flash on the mark iv.

I got it sorted now. For some reason when I put it in the /tmp/ folder instead of the root directory, it worked.

Having problems getting this script to run. See error below:

A. Yes I have been able to connect to the webui without any hitch. It just happened when I turned the pineapple on and all the lights were solid. I couldn't log into the webui so I hit the reset button on the bottom and thats when the WPS light kept flashing and would not go solid. B. I used the ac adapter that came supplied with it when I bought it. See above. This is new behavior.

Ok thanks. Just checking. I seem to have to leave my usb drive out till it fully loads, otherwise it gives me an error when trying to open the webui.

When i put in the power adapter. All the lights come on and then the WPS light flashes for 1 1/2 before it stays solid and the WLAN light lights up. Is this normal?

Yes, the correct com port is being used. As I stated before, I can see all the dialog in the putty terminal connection, but for some odd reason I can't send any commands to it. By default it picks option #3 for me because it does not sense that I'm trying to push the 1 key for option #1. I tripled checked that all the setting were correct in both putty and my com port in device manager in windows 7. I have no clue what else could be causing this issue.

So I tried to use another program called secureCRT and it is doing the same thing. For some reason, the shell is not responding to my keyboard. I have tried it on 2 computer already. I guess I will exchange the pineapple for another one then. P.S. For those of you who are thinking I didn't have the settings right for the com port, yes I have checked numerous times that the settings are correct in device manager as well as putty settings. I basically followed Mr. Protocol's video step-by-step. Not sure why else the terminal does not respond to any keys. I also did a google search and found that sometimes with putty you have to push $$$ before to get putty to respond. That doesn't work.

Welp I got it to communicate, but when it loads up, I can see the 3 selections, but it doesn't prompt me. There is a counter on the right side that counts down from 3. It loads by itself and gets stuck at "please press enter to activate this console". Basically it won't let me push "1" from the get go. :/ and I can't get past the "please press enter to activate this console". It doesn't do anything when I push "enter".

Super that worked! How did you know the wires were switched around? Thanks

I am trying to do a clean flash on my Mark IV, but am stuck at the putty window with the cursor (see below). I am not sure what is going on. I followed the pinned guide by Mr.Protocol, but it is not working. I checked that my com3 port is working and all the connections are in the right order on the USB to TTL serial connection. I am running windows 7 64-bit and trying to connect through putty. Any help would be appreciated. Thanks. P.S. The connector I bought was from here: http://www.ebay.com/itm/170809155735?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649