Jump to content

xXNirvashXx

Active Members
  • Posts

    25
  • Joined

  • Last visited

Posts posted by xXNirvashXx

  1. Hey Guys,

    I do a bit of walking for fitness and as a concept would I be able to use Wifi Pineapple as Google style BSSID and other metadata surveyor? So say I put the pineapple in my bag and just walk my usual route and see how many wifi, bssid, signal strength ect... I can pick up ?

    I've tried Site Survey addon but it seem there is no way to make a file with all the data and I'd have to constantly look at my phone as I walk.

    Thanks :)

  2. You might try SSHing into the pineapple and trying to setup the connections manually... The Network Manager Infusion is just a shortcut for all of those commands which is why I love it. But it is possible to do it all from the command line.

    Thanks I'll give it a go.

  3. Sorry I kind of glossed over the DHCP request part of your post... When you hit DHCP request an IP address should come up on the screen. If you aren't seeing that your wlan1 (external) device isn't actually connecting. What type of security does the AP that wlan1 is trying to connect to use?

    Nah, you right mate.

    I am definitely not seeing the IP after DHCP request. I can use the same wifi stick on Win8 to connect to the WIFI.

    Here is the security WIFI uses.

    Capture5.JPG

  4. Well, I can enable both of wlan0 and wlan1, however I just cannot get internet on the Pineapple through the wifi. My ICS settings are share wlan1 ( external) to wlan0 ( internal).

    I dont think its connecting to the WIFI. I've selected all of the right settings and found my SSID, but I can't see the Pineapple on the LAN doing nmap of my lan.

  5. Hey Guys,

    This is very silly, but I can not get the Network Manager 1.9 Infusion to work, which seem very straightforward. So what I want is not to bother with CAT5 and to say connect to my home WIFI with wifi1 and turn the Karma on wifi0.

    I've got Mark IV with 2.8.1 - cache cleared and factory reset.

    Pineapple automaticly wants to use my external wifi1 as AP with "pineapple 05:02".

    I've adjusted the wlan1 to my WIFI settings.

    Capture1.JPG

    I hit [DHCP Request] . Its trying to get IP but how do I tell if it worked or not? Nothing on the page changes.

    My ICS settings set too.

    Capture3.JPG

    When I try to add the in built wifi0 by hitting enable in Logical Interfaces, it doesn't come up and if I hit it too many times in a raw the "wlan0 disabled [Enable]" disappears and I have to refresh the page. Or is the Physical Interface radio0 [-] - HWAddr [00:0f:04:b2:48:a1] Pineapple's in built wifi? Either way "pineapple 05:02" SSID disappears , and If I unplug CAT5 I cant get to http://172.16.42.1:1471 which I assume means [DHCP Request] didnt work.

    What am I missing? Is there another, way to go about this? What shoudl my /etc/config/wireless look like :/

    Thanks :)

  6. Thanks Tyler,

    I have ran chmod +x ~/wireless_connect.sh, and when I try with sudo I get " sudo : not found".

    Even doing it your way of manual setup, I get stuck at the same point of udhcp -i wlan1:

    udhcpc (v1.19.4) started
    Sending discover...
    Sending discover...
    Sending discover...
    After a long wait I get :

    Sending select for 172.16.42.155...

    Lease of 172.16.42.155 obtained, lease time 43200
    udhcpc: ifconfig wlan1 172.16.42.155 netmask 255.255.255.0 broadcast 172.16.42.255
    udhcpc: setting default routers: 172.16.42.1
    route: SIOCADDRT: Network is unreachable

    route

    root@Pineapple:~# route

    Kernel IP routing table
    Destination Gateway Genmask Flags Metric Ref Use Iface
    172.16.42.0 * 255.255.255.0 U 0 0 0 br-lan
    172.16.42.0 * 255.255.255.0 U 0 0 0 wlan1
  7. Hmm sorry guys,

    Kind of struggling as well.

    root@Pineapple:~# ./wireless_connect.sh

    Current MAC: c8:3a:35:c0:22:b7 (unknown)
    ERROR: Can't change MAC: interface up or not permission: Invalid argument
    Successfully initialized wpa_supplicant
    udhcpc (v1.19.4) started
    Sending discover...
    Sending discover...
    Sending discover...

    And Putty just sits there like that until I ctrl+c it. :( Pineapple firmware is 2.8.0

  8. Hey Guys,

    Haha i swear I’ve got the worst luck with wifi pineapples ever. After receiving my new pineapple replacement , the first thing I did was to update it to 2.5.0 I think it was. I did it from http://172.16.42.1/pineapple page but after update the http://172.16.42.1/pineapple automatically redirects me to http://172.16.42.1/redirect.php and the page gets stuck in constant loop of refreshing. I can still ssh into pineapple and after multiple reboots I still not sure how to fix it.

    Did it somehow get bricked :'(

    Thanks

    **************

    Never mind fixed it :)

  9. from what you said "Hornet" this is a stock board and is not flashed with the pineapple firmware yet, if you got this from the hakshop I would contact them and maybe a replacement or if your willing to attempt to flash it under there instructions.

    I know the ones that come with openwrt can sometimes be flashed just like how the mk4 firmware does it.

    Thank you, I will double check when I get home but I am almost 100% sure that the SSID last night was "Hornet". It is from hakshop, I just received it about 4 days ago. I will shoot them an email than to see what they think I should do next.

    Thanks again

  10. No sorry, 172.16.42.1/pineapple is unreachable and times out. That is the problem, I can't see it, nor can I ping 172.16.42.1. I can see the "Hornet" SSID but even when I connect wirelessly, I get wrong IP (eg 192.168.2.234) and still cant get to 172.16.42.1/pineapple, to even try to update the pineapple.

    It is as if the DHCP is broken and keeps giving out weird IP, but when I try to manually set one to something within pineapple's range I still cant see the 172.16.42.1/pineapple.

  11. Hi,

    This may be a bit of a silly question, but I am having trouble with getting to web interface of brand new WiFi Pineapple Mark IV . I have tried following instructions for Windows and Linux from basic shared internet setup, with no luck ( cant even ping 172.16.42.1) I have tried leaving it on DHCP but the IP i get given is rubbish along the lines of 192.168.2.234 and not 172.16.42.100-150 that i am supposed to be getting. I tried manually setting the IP something like 172.16.42.150 and still no luck, and i still cant ping 172.16.42.1. I have tried reseting the pineapple using the reset button in a hope it would revert back to giving out right IP with no luck.

    Any tips on what i am doing wrong?

    Thanks :)

  12. You just want to make sure you wireless card's chipset is supported in Linux and if it is able to be put into monitor mode.

    #iwconfig wlan0 mode monitor

    AirPCAP is just an external wireless adapter with special drivers to allow for monitor mode. This package, I believe, is the only way to put a card into monitor mode in Windows

    When i set my card into monitor mode and capture packets and no point its asks me for my key , and when i try to analyze them i get nothing. No imiges and anything like it. where is it do i have to enter my encryption code?

  13. The easiest way to way to get a wifi card into monitor mode is in Linux. (for windows google AirPCAP)

    Your card's chipset must support it and you have to have linux drivers that support it (google YOUR CARD chipset) or (google YOUR CARD linux)

    after you have that all set up and working, you can use wireshark to capture the traffic. you'll need to enter the wireless key into wireshark (if there is one) so it can decrypt the packets.

    thankz, but after i seach adn find my cheapset what do i do then? i mean what software do i use (for lunix?)

    and as for windows all i found about AirPCAP is that its an external actual wifi card and not a software...

    I have tried to put my card in to monitor mode using microsofts Network Manager and then also oppening Wireshack but i wasnt able to capture any packets as my wifi addapter was gone from the list and was replaced by "Microsoft"

    and the packets i captured with Network Manager i didnt need network key but i wasnt able to get anything using Net Witness or Net Miner

  14. On a switched network you will only see broadcast, mulitcast, and traffic destined for your hardware address (there is one more type, but i don't remember it). On a switched network (yes wireless routers are switched networks) you needs to either a) set up a network tap or b. use a man-in-the-middle attack to see all network traffic. c) put your wireless card into monitor mode and sniff all wireless traffic.. More detail follows.

    a) you can use a hub. connect target, your computer and the switch all to the hub. The biggest limitations to this is that a true hub is hard to come by these days. You could purchase a network tap from a company like www.netoptics.com.

    b. tools like ettercap, sslstrip, the middler, cain are great software approaches at MitM attacks. Jasager/Karma or just a correctly configured rouge AP are for wireless MitM attacks

    c) if you know the encryption key, or its an open wifi point, you can capture any traffic on a particular channel just by setting your wifi card into a listen only mode (monitor mode). Capture the data and then analyze it offline.

    thank you

    i will try to read more in to option B )

    How do i do it using part c) how do i set my wifi card in to a monitor mode?

  15. Hey,

    eps 514 showed some really great tools but....

    1st) how did they capture packets from other pcs ? I don’t think I’ve heard them saying ... but were they connected to a switch?

    2nd) every time I try this on my own network I only manage to capture packets from my own pc only. I know this is because I use router and not a switch, but how were they able to do it in the show?

    What I accentually want to play around with is :

    To say go to a website on my iphone and capture packets on my laptop via wireless and analyse them with those tools. Can that be done?

    Thank you

  16. "You might want to install the `Autoconf' and `GNU m4' packages."

    Backtrack 4 is based around Ubuntu, which is based on Debian. Debian uses the Advanced Packaging Tool, also known as apt, which allows you to install packages with the command "apt-get install blah". So enter "apt-get update" followed by "apt-get install autoconf" and "apt-get install m4". Then try and install airpwn again.

    I wrote a very detailed how-to on installation of AirPWN and execution of injecting code into web pages on my blog --> http://timashley.me/node/100

    Thank you ;)

  17. i cant install it either. cant get past the "make" in airpwn dir

    cd . && /bin/bash /home/xxazazelxx/airpwn-1.4/missing --run autoheader
    /home/xxazazelxx/airpwn-1.4/missing: line 52: autoheader: command not found
    WARNING: `autoheader' is missing on your system.  You should only need it if
             you modified `acconfig.h' or `configure.ac'.  You might want
             to install the `Autoconf' and `GNU m4' packages.  Grab them
             from any GNU archive site.
    rm -f stamp-h1
    touch config.h.in
    cd . && /bin/bash ./config.status config.h
    config.status: creating config.h
    config.status: config.h is unchanged
    make  all-am
    make[1]: Entering directory `/home/xxazazelxx/airpwn-1.4'
    if gcc -DHAVE_CONFIG_H -I. -I. -I.     -g -O2 -MT airpwn.o -MD -MP -MF ".deps/airpwn.Tpo" -c -o airpwn.o airpwn.c; \
    	then mv -f ".deps/airpwn.Tpo" ".deps/airpwn.Po"; else rm -f ".deps/airpwn.Tpo"; exit 1; fi
    In file included from airpwn.c:46:
    conf.h:21:30: error: python2.4/Python.h: No such file or directory
    In file included from airpwn.c:46:
    conf.h:33: error: expected specifier-qualifier-list before ‘PyObject’
    airpwn.c: In function ‘spoof_response’:
    airpwn.c:401: error: ‘conf_entry’ has no member named ‘response_len’
    airpwn.c:402: error: ‘conf_entry’ has no member named ‘pyfunc’
    airpwn.c:403: error: ‘PyObject’ undeclared (first use in this function)
    airpwn.c:403: error: (Each undeclared identifier is reported only once
    airpwn.c:403: error: for each function it appears in.)
    airpwn.c:403: error: ‘args’ undeclared (first use in this function)
    airpwn.c:405: error: ‘value’ undeclared (first use in this function)
    airpwn.c:405: error: ‘conf_entry’ has no member named ‘pyfunc’
    airpwn.c:412: warning: assignment makes pointer from integer without a cast
    airpwn.c:435: error: ‘conf_entry’ has no member named ‘options’
    airpwn.c: In function ‘process_ip_packet’:
    airpwn.c:470: error: ‘conf_entry’ has no member named ‘next’
    airpwn.c:509: warning: ignoring return value of ‘write’, declared with attribute warn_unused_result
    airpwn.c:510: warning: ignoring return value of ‘write’, declared with attribute warn_unused_result
    airpwn.c:511: warning: ignoring return value of ‘write’, declared with attribute warn_unused_result
    make[1]: *** [airpwn.o] Error 1
    make[1]: Leaving directory `/home/xxazazelxx/airpwn-1.4'
    make: *** [all] Error 2
    

    does anyone have any noob friendly tips on how to install it? thankz

×
×
  • Create New...