Bitstream

Looks like 2.1.2 is newest for Mk3: http://forums.hak5.org/index.php?showtopic=25201

I'm curious as to what size your Fit is? I"m sure it doesn't matter but maybe there is just a bad batch of the 16gb Fit's. When I talked to SanDisk to get an RMA the guy mentioned they have had "a few" 16gb Fit's exhibit the same issue I had. On the first one I was running it from AC plug out of a APC Smart-UPS 1400 and the second one was from using a fully charged Voltaic V60. Nah, it doesn't come across that way to me...but I really cannot see how I am causing it. I am doing nothing much different than I did with the earlier firmware builds and I had no issue then. The only thing I am really doing different is putting more modules on now since more are available (and no I do not think that has anything to do with it...I am just saying that is really the only thing different I am doing with the new firmware than I did with the old.

I should of mentioned that I had NO problems with any of the firmware versions prior to 2.0.0 and I had ran all of them...it was only after flashing to 2.0.0 that I lost both flash drives. I had the same setup 2gb swap/14gb...I had sslstrip, nmap, tcpdump, etc. and all worked fine...up till the point the flash drives quit working. Like I said, I can see me possibly getting one bad flash drive but now that it has happened to two of them I think something is going on. I have the usb hub from hakshop but was not using it when the drives died. I just had them plugged straight into the pineapple and the pineapple itself was in a pelican 1060 case. Maybe the flash drives did get too hot but when the last one failed I only had the pineapple on for less than 10 minutes.

Interesting...I can see one possibly being bad but having two do the same thing astounds me.

Okay...I don't know WTF is causing this but it has now happened twice. I format a SanDisk Cruzer Fit 16gb as outlined in http://forums.hak5.org/index.php?showtopic=25882 and install all the modules to it. It works fine for a week or so then on boot it is no longer there...I take it out of the pineapple and plug it into one of my linux laptops and it shows up in /dev but it cannot be mounted. Always errors out with an error saying it is read-only (but it still will not mount). First time it happened I chalked it up to being a bad flash drive and SanDisk is even replacing it under warranty. But it just happened to a second SanDisk Cruzer Fit 16gb so WTF is going on??? Anybody else had this happen to them?

I ran into the same thing. Now my 16gb SanDisk Cruzer Fit says it is read-only...no matter what machine I put it in...and I cannot fdisk it or anything. I used that card under all previous pineapple versions just fine...I thought my card just went bad but now that someone else is having the exact same issue under 2.0.0 it makes me wonder what is going on.

Has anyone been able to get the Pantech UML290 4G dongle to work with the MkIV? If so, I'd appreciate seeing your 3g.sh.

Changed it to: list 'dhcp_option' '3,192.168.1.254' and now it is getting passed to the client as it should...wacky imho.

I have dnsmasq setup on the fon to give out IP addresses and also to set the route and default gateway. It gives out IP addresses fine: Example from client: wlan0 Link encap:Ethernet HWaddr xx:xx:xx:xx:xx:xx inet addr:192.168.1.225 Bcast:192.168.1.255 Mask:255.255.255.0 Routing table from the client: Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 * 255.255.255.0 U 0 0 0 wlan0 default 192.168.1.1 0.0.0.0 UG 0 0 0 wlan0 resolv.conf from client: domain lan search lan nameserver 208.67.222.222 So it is getting an ip and setting the dns just as I want but it is leaving the default gateway to the IP of the fon and not what I have it set to do. Here is the configuration for dnsmasq setup on the fon: root@OpenWrt:/etc/config# cat dhcp config dnsmasq option domainneeded 1 option boguspriv 1 option filterwin2k '0' #enable for dial on demand option localise_queries 1 option local '/lan/' option domain 'lan' option expandhosts 1 option nonegcache 0 option authoritative 1 option readethers 1 option leasefile '/tmp/dhcp.leases' option resolvfile '/tmp/resolv.conf.auto' config dhcp lan option interface lan option start 100 option limit 150 option leasetime 2h option dhcp_option 'lan,3,192.168.1.254' option dhcp_option 'lan,6,208.67.222.222' config dhcp wan option interface wan option ignore 1 Here are the network settings: root@OpenWrt:/etc/config# cat network # Copyright © 2006 OpenWrt.org config interface loopback option ifname lo option proto static option ipaddr 127.0.0.1 option netmask 255.0.0.0 config interface lan option ifname eth0 option type bridge option proto static option ipaddr 192.168.1.1 option netmask 255.255.255.0 option dns '208.67.222.222 208.67.220.220' option gateway 192.168.1.254 As you can see in the dhcp configuration I have it set for option dhcp_option 'lan,3,192.168.1.254' so why is it staying as 192.168.1.1 on the clients??? I am sure I am probably overlooking something simple but am brain dead at the moment.

Yup...

Yeah, I know...just answering his question is all...

Are you sure it is a power issue as I have powered mine from the AC outlet and still encounter drops of wifi connections...mainly my connection to the fon from the mitm laptop. Been pissing me off trying to figure out why that link drops for no apparent reason.

I just threw a meter on mine and it was 6.96 volts on a full charge.

How are you connecting it to the fon? Did you solder a cable onto it terminals cause if so I am wondering how you then can get it to fit into the charger as it is already a tight fit.

All 4 of mine are 87

All 4 of them I recently bought from there were 0.7.1 r1. I bought one...then 2 weeks later another 3.

Yup, that is exactly how I did it...

Thanks for the attempt!

Have you tried the ICS connection from a Windows VM image? Just curious if it works okay in that situation...

Pineapple arrived today...notice in the first pic that the stamps didn't get cancelled. The pineapple did suffer some damage as shown in the second pic.

Anyone got Jasager to work on Linux using an EVDO card to route the traffic in/out to the internet?

Mine took 6 days from time of ordering to arrival in Texas.

I ordered one from them a couple of weeks ago and it came with r1 on it. Can't say what you will get of course but mine was fine.

Hmmm, for me, the Jasager page is protected if you go to it on port 1471 but not if you connect straight to port 80...then it will just happily forward you with no authentication required. The webif.html is protected on port 80 though.

Is the WLAN LED supposed to light up after the whole process is complete as it does not on mine irregardless of whether Karma is turned on via the web interface or not...