hanshaze

lanturtle
Find the error......

4 posts in this topic

Posted (edited)

My goal is to make my LanTurtle accessible over the entire LAN or the very best in the WAN.

For this I proceed as follows

Step 1: Without LanTurtle plugged in -> Windows 10 -> ipconfig

001_ipconfig.png.9e1584822fcd5de30d7f54099a63829b.png

Step 2: LanTurtle via Ethernet cable cable to the router, other side -->  USB at the laptop -> ipconfig

002_ipconfig.png.c0fbe29ad7893eaefe276a67a8998e0c.png

 

Step 3 SSH into the LanTurtle

003_ssh.png.b43f1714d745c17fa6c264e449fbef44.png

Step 4: Update modules

004_turtle.thumb.png.0c4fe625124bdea5cf67c50af126e6ed.png

005_turtle_ipconfig.png.f39c8bd33597b542dd08854f9318759f.png

Now, if i plug out the LanTurtle after Step 4 and connect it to the LAN like in those two Pics below i cant receive the LanTurtle over LAN anything else....

590807e29460a_WhatsAppImage2017-05-02at05_48.57(1).thumb.jpeg.9b8bfebfc16e259ce3b3758fbc3628c9.jpeg590807e60517c_WhatsAppImage2017-05-02at05_48_57.thumb.jpeg.94333fa655cbe6801cea511b1fbce6e5.jpeg

What is my fault?

005_turtle_ipconfig.png

Edited by hanshaze
0

Share this post


Link to post
Share on other sites

So if I understand correctly, you have the LT plugged into a laptop which has the internal 172.16.84.1 address and also into the LAN which received the 192.168.178.31/24 address correct ? 

* From here, you mention that you plug it through a direct power source ? 

What I get from here is that the 172.16.84.1/24 scheme is not accessible because the interface it is responsible for connecting to when plugged into a device through USB is not accessible as it's just a power source. 

You should technically still have a LAN connection, however. 

Also, if you're looking to access the turtle remotely you will want to look into setting up the Open VPN server either at your home on a Raspberry PI or on a router / networking device if it supports it. Hope I understood your hang ups here. 

 

0

Share this post


Link to post
Share on other sites

Posted (edited)

Thanks for your answer......

Yes, the LT is plugged to a direct power source.....

So at least one of the two IPs should be achievable, but this is not the case...

Do i have to forward Port 22 for 172.16.84.1? Or for 192.168.178.xx?

For now this is the output of my screen

neu.png

Edited by hanshaze
0

Share this post


Link to post
Share on other sites

Well, the 172.16.84.1 interface would not be available because there is no interface to connect to if it's just a power source as this interface relies on a physical interface to attach to. As for the 192.168.x.x failing, did you set this statically ? It's possible the ip changed. 

Try doing a ping sweep of your LAN to ensure it is reachable - `nmap -sS -p 22 --open 192.168.178.1/4`

0

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.