sleepyalexks Posted December 30, 2015 Share Posted December 30, 2015 Hi, it is my first LAN Turtle, I ordered it as Bundle from the US Store. I did the Update to V2 with Putty & Network cable throug the LanTurtle I am not able to install anything from the Directory. I tryed factory Default reset with the .bin of your Website. Stil the same Problem. In the List of the Modules there is no X by Modulemange. When I select it, it tells me Current Status:Stopped And Bootup Status: Enabled When I go to configure I can select Modules from Directory but nothing is installed in the end. I tryed everthing! Is there a solution? Quote Link to comment Share on other sites More sharing options...
m40295 Posted December 31, 2015 Share Posted December 31, 2015 I belive the start stop is not needed configure will allow you to add modules from the site but it does not need to be started and stopped Quote Link to comment Share on other sites More sharing options...
iamtags Posted January 2, 2016 Share Posted January 2, 2016 At least in my experience, I have this same problem, and am unable to download modules. I cannot say for sure it is due to module manager not starting, but seems like may be related. As in OP comments, I immediately checked for and downloaded updates (as instructed). This updated my firmware from v1 to v2. I could not download modules and modulemanager wouldn't start. Since I could not download modules, I followed instructions on the wiki and reflashed. I am running version 2 as downloaded from downloads.lanturtle.com. I successfully: -Acquire IP Address -SSH to Turtle -Change Password -Update Turtle from turtle shell -Connect and view list of available modules -Successfully reflash with latest firmware (though issues persist) I cannot: -Start the ModuleManager Service ​Selecting modules > modulemanager > start == screen indicating press OK or CTRL+C to exit...service does not start Changing bootup status to "enabled" does not start the manager, even after performing above and/or rebooting accessing lower-level shell and entering #start modulemanager provides a message "commands will be executed using /bin/sh" and a job is created, though modulemanager still does not run -Download Modules I navigate to modules > modulemanager > configure > directory > yes > [select any module, all are displayed] == message "installed modules:" and no modules are installed I feel like this may be a firmware issue. I have a friend who received a turtle in same general time and did not update to v2. He is able to download and run modules without any problems. Could we acquire have an official download made available of the old v1 of the firmware as a temporary fix/troublehsooting step? Please advise, and thank you in advance for your help, Quote Link to comment Share on other sites More sharing options...
sleepyalexks Posted January 2, 2016 Author Share Posted January 2, 2016 It feels good to see that I am not alone. Quote Link to comment Share on other sites More sharing options...
bored369 Posted January 2, 2016 Share Posted January 2, 2016 I have a second LanTurtle i purchased and received around November 2015. I haven't used it at all yet, but seeing this thread I thought I'd try it out. My first LanTurtle worked out of the box without issues and has been deployed/operating as I need it to for a few months now. I started out first by factory resetting the turtle using latest bin available on lanturtle.com and uploading through the web interface, just so I could be sure it was on the same bin. I was able to go into the Module Manger-Directory and download/install all of the modules without an issue. Confirmed when I backed out of the module manager all the modules were listed and I tested out System Uptime just to be sure one was working. it's important to note, module manger is never going to be able to start or enable. There's no reason to as everything is done in the configure. Maybe there is something else going on, but I'm not sure where to have y'all check for errors or anything past just letting you know I have one that worked as of today on the latest firmware bin. Quote Link to comment Share on other sites More sharing options...
sleepyalexks Posted January 4, 2016 Author Share Posted January 4, 2016 Solution seems to be here https://forums.hak5.org/index.php?/topic/36507-cant-download-modules/ I check out if it works for me, seems to be the same Problem Quote Link to comment Share on other sites More sharing options...
sleepyalexks Posted January 11, 2016 Author Share Posted January 11, 2016 Still no solution, @ iamtags I guess it is the best for us to ask for refund :-( The case in the link is Long time ago & does not match with our case. Quote Link to comment Share on other sites More sharing options...
iamtags Posted January 12, 2016 Share Posted January 12, 2016 Solution seems to be here https://forums.hak5.org/index.php?/topic/36507-cant-download-modules/ I check out if it works for me, seems to be the same Problem Thanks for checking, I also tried but no luck Still no solution, @ iamtags I guess it is the best for us to ask for refund :-( The case in the link is Long time ago & does not match with our case. I really don't want to have to request a refund but without some official support I don't know what else to do. As bored369 indicates, The problem isn't necessarily the fact that modulemanager wont start, since he can download without that "service." Our problem is that modules will not download. Possible to rename your post? I may post with a different title to see if we can get a fix. Honestly if I could get the v1 firmware I'd like to see if it works Quote Link to comment Share on other sites More sharing options...
ironclaw Posted January 21, 2016 Share Posted January 21, 2016 I just updated my Lan Turtle to V2 with a manual upgrade, and I'm having the same issue. Quote Link to comment Share on other sites More sharing options...
Darren Kitchen Posted February 2, 2016 Share Posted February 2, 2016 Hey guys I did a video on this topic -- I hope it helps. 2 Quote Link to comment Share on other sites More sharing options...
bored369 Posted February 2, 2016 Share Posted February 2, 2016 Hey guys I did a video on this topic -- I hope it helps. That was an awesome video! Learned a lot about how the modules are setup on the turtle filesystem and how it all works in the background. Thanks for that!!! Quote Link to comment Share on other sites More sharing options...
Hak5Mewbie Posted March 1, 2017 Share Posted March 1, 2017 I have just recived my lan turtle, i have the same problem PLEASE, someone help me!, what am i going to do?, just after the update modules stopped. Quote Link to comment Share on other sites More sharing options...
bashincajun Posted May 23, 2017 Share Posted May 23, 2017 have you tried reseting it i have had do do that on my last one when i got it.. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.