sempf Posted February 28, 2014 Share Posted February 28, 2014 I am not a Linux guy or a network guy. Trying to learn, and clearly missing something. My process so far: Boot MK4 Plug into ethernet of laptop Can see Pineapple control center Clients can connect to MK4 wifi Clients cannot see the internet When the wired connection is enabled, the laptop cannot see the interent If the wired connection is disabled, the laptop can see the internet I have tried to run the script with the wired connection enabled and disabled, as I read elsewhere. I am running the script with sudo From what I understand, clients who connect to the MK4 wireless should be able to browse the internet through my laptop's wireless connection. That isn't happpening. Here is my ifconfig, my iwconfig, and the mk4.sh setup. Any help appreciated. Mark IV2.8.1 FirmwareKali Linux 1.0.1 root@testing:~# iwconfigwlan0 IEEE 802.11bgn ESSID:"Lambert"Mode:Managed Frequency:2.462 GHz Access Point: E0:91:F5:0F:4D:24Bit Rate=54 Mb/s Tx-Power=27 dBmRetry long limit:7 RTS thr:off Fragment thr:offEncryption key:offPower Management:offLink Quality=55/70 Signal level=-55 dBmRx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0Tx excessive retries:0 Invalid misc:14 Missed beacon:0 lo no wireless extensions. eth0 no wireless extensions. root@testing:~# ifconfigeth0 Link encap:Ethernet HWaddr c8:0a:a9:74:a0:bainet6 addr: fe80::ca0a:a9ff:fe74:a0ba/64 Scope:LinkUP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1RX packets:13034 errors:0 dropped:6 overruns:0 frame:0TX packets:9462 errors:0 dropped:0 overruns:0 carrier:33collisions:0 txqueuelen:1000RX bytes:956967 (934.5 KiB) TX bytes:673537 (657.7 KiB) lo Link encap:Local Loopbackinet addr:127.0.0.1 Mask:255.0.0.0inet6 addr: ::1/128 Scope:HostUP LOOPBACK RUNNING MTU:65536 Metric:1RX packets:133 errors:0 dropped:0 overruns:0 frame:0TX packets:133 errors:0 dropped:0 overruns:0 carrier:0collisions:0 txqueuelen:0RX bytes:8718 (8.5 KiB) TX bytes:8718 (8.5 KiB) wlan0 Link encap:Ethernet HWaddr 78:e4:00:67:bd:f9inet addr:192.168.240.124 Bcast:192.168.240.255 Mask:255.255.255.0inet6 addr: fe80::7ae4:ff:fe67:bdf9/64 Scope:LinkUP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1RX packets:308870 errors:0 dropped:0 overruns:0 frame:0TX packets:35977 errors:0 dropped:0 overruns:0 carrier:0collisions:0 txqueuelen:1000RX bytes:115260608 (109.9 MiB) TX bytes:3435412 (3.2 MiB) Pineapple Netmask [255.255.255.0]:Pineapple Network [172.16.42.0/24]:Interface between PC and Pineapple [eth0]:Interface between PC and Internet [wlan0]:Internet Gateway [192.168.240.1]:IP Address of Host PC [172.16.42.42]: 192.168.240.124IP Address of Pineapple [172.16.42.1]: _ . ___ \||/ Internet: 192.168.240.1 - wlan0( _ )_ <--> [___] <--> ,<><>, Computer: 192.168.240.124(_ _(_ ,) \___\ '<><>' Pineapple: 172.16.42.0/24 - eth0 Browse to http://172.16.42.1:1471 -- Happy Hacking! Quote Link to comment Share on other sites More sharing options...
Mr-Protocol Posted February 28, 2014 Share Posted February 28, 2014 Give this a watch and see if it helps. It may be something with your network manager trying to automatically make connections. Network managers should be disabled. Quote Link to comment Share on other sites More sharing options...
sempf Posted February 28, 2014 Author Share Posted February 28, 2014 Hey, that worked just fine! I needed to carefully make sure my previous testing didn't screw things up, but when I did, magic. Thanks a lot for the fast response!! S Quote Link to comment Share on other sites More sharing options...
Mr-Protocol Posted February 28, 2014 Share Posted February 28, 2014 Not a problem. Glad you got it up and running. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.