Search the Community
Showing results for tags 'mark4'.
-
Hi there ! my setup AP: AP121U (ALFA) - external Wifi-card: AR9271 (ALFA) If I flash the pinapple firmware on the AP121U, will it recognise the AR9271 and will I be able to use it as an range extender ? I need to bridge both wireless interfaces. Right now, the AP121U is running openwrt(lede) and I cannot figure out how to do it. So I am hoping that maybe the Pinapple firmware makes it easier. Any help very very much apreciated. Thanx !!
- 1 reply
-
- bridge
- networking
-
(and 1 more)
Tagged with:
-
Hello, can someone sell me a working WiFi Pineapple Mark V or Mark IV (Better mark5) ? I will be very grateful. PM or email me at 0ntgo0@protonmail.com
-
Hi , Is there any infusion available for Deauth or wifi jammer for Mark IV? or can any one suggest how to build one if not available
-
Hello, I just received my wifi pineapple mark v, I put sslstrip running, but I only worked on hotmail.com, if I try to go to facebook or youtube the security HTTPS still on, can someone help me on this?. thank you
-
Hi all, i'm trying to setup the internet connection sharing in ubuntu, but when i run the script don't do nothing, here is some screenshots about my configuration: hackzilla@Notebook:~$ iwconfig lo no wireless extensions. eth1 IEEE 802.11 Access Point: Not-Associated Link Quality:1 Signal level:171 Noise level:199 Rx invalid nwid:0 invalid crypt:2 invalid misc:0 eth0 no wireless extensions. hackzilla@Notebook:~$ iwconfig lo no wireless extensions. eth1 IEEE 802.11 Access Point: Not-Associated Link Quality:1 Signal level:171 Noise level:199 Rx invalid nwid:0 invalid crypt:2 invalid misc:0 eth0 no wireless extensions. hackzilla @ Notebook: ~ $ ifconfig eth0 Link encap: Ethernet direcciónHW 00:23:5 a: a4: 7b: 8c Inet6 addr: fe80 :: 223:5 aff: fea4: 7b8c/64 Scope: Link ACTIVE BROADCAST RUNNING MULTICAST MTU: 1500 Metric: 1 RX packets: 348 errors: 0 lost: 0 overruns: 0 frame: 0 TX packets: 194 errors: 0 Lost: 0 overruns: 0 carrier: 0 collisions: 0 long.colaTX: 1000 RX bytes: 23439 (23.4 KB) TX bytes: 25429 (25.4 KB) Interrupt: 46 Base address: 0xA000 eth1 Link encap: Ethernet direcciónHW 00:21:00: f1: f3: a7 Direction. inet: 192.168.1.100 broadcast software.: 192.168.1.255 Mask: 255.255.255.0 Inet6 addr: fe80 :: 221: ff: fef1: f3a7/64 Scope: Link ACTIVE BROADCAST RUNNING MULTICAST MTU: 1500 Metric: 1 RX packets: 397087 errors: 0 lost: 0 overruns: 0 frame: 1087604 TX packets: 254160 errors: 171 Lost: 0 overruns: 0 carrier: 0 collisions: 0 long.colaTX: 1000 RX bytes: 551948883 (551.9 MB) TX bytes: 25213181 (25.2 MB) Interruption: 18 lo Link encap: Local Loopback Direction. inet: 127.0.0.1 Mask: 255.0.0.0 Inet6 addr ::: 1/128 Scope: Host LOOP ACTIVE RUNNING MTU: 16436 Metric: 1 RX packets: 7937 errors: 0 lost: 0 overruns: 0 frame: 0 TX packets: 7937 errors: 0 Lost: 0 overruns: 0 carrier: 0 collisions: 0 long.colaTX: 0 RX bytes: 650816 (650.8 KB) TX bytes: 650816 (650.8 KB) do you have any idea why the internet connection is on eth1 if i'm connected to my house wifi, so, should not be wlan0? Thanks!
- 7 replies
-
- ics problem
- linux
-
(and 4 more)
Tagged with: