khanbari

Have you tried doing it again? The reset might have interrupted during the process.

HI, Another query related to this. wifi adapter seems to be working fine for me. Interfaces provided by the nano are two. Corrent me on this. One is for open access and the other is management access point which is allows WPS. clients connected to the open interface are visible in the dashboard under connected clients and the the one connected to the management interface are not. But any filtering or spoofing enabled will be reflected to both the interfaces. What i wanted is to have both as WPS enabled instead of one. Any suggestions are welcome. Thanks in advance for the support.

Thanks for the prompt response. Just to confirm will the below do? https://www.amazon.in/dp/B01FY0012M/ref=cm_sw_r_wa_apa_i_iXt-yb5CY4RD4

Antenna upgrade of Nano. Hi experts, I'm looking to upgrade the antenna for my nano, any suggestions on the possible limitation and the supported brand. Thanks

Hi Did a factory reset and plugged in the wifi again. It's working. Thanks a lot :)

Hi Thanks again for the prompt response. I'm using the one you mentioned.

Just to update on the config i get before and after. When i connect the wifi adapter then only i see wlan1 in wifi client mode and once removed its empty. Below are the cmd readings. I see wlan1 only appears when i connect the wifi adapter. Before connecting wifi adapter: root@Pineapple:~# iwconfig lo no wireless extensions. usb0 no wireless extensions. wlan0-1 IEEE 802.11bgn Mode:Master Tx-Power=17 dBm RTS thr:off Fragment thr:off Power Management:off wlan0 IEEE 802.11bgn Mode:Master Tx-Power=17 dBm RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. br-lan no wireless extensions. root@Pineapple:~# ifconfig br-lan Link encap:Ethernet HWaddr 00:C0:CA:91:9E:0B inet addr:172.16.42.1 Bcast:172.16.42.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:9292 errors:0 dropped:1591 overruns:0 frame:0 TX packets:7620 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1333577 (1.2 MiB) TX bytes:3297606 (3.1 MiB) eth0 Link encap:Ethernet HWaddr 00:C0:CA:91:9E:0B UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:4 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:654 errors:0 dropped:0 overruns:0 frame:0 TX packets:654 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:56426 (55.1 KiB) TX bytes:56426 (55.1 KiB) usb0 Link encap:Ethernet HWaddr 96:1C:52:E9:27:B7 inet addr:192.168.42.189 Bcast:192.168.42.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2138 errors:0 dropped:10 overruns:0 frame:0 TX packets:2024 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:979694 (956.7 KiB) TX bytes:453328 (442.7 KiB) wlan0 Link encap:Ethernet HWaddr 00:C0:CA:91:6F:22 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:30 errors:0 dropped:0 overruns:0 frame:0 TX packets:3060 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2805 (2.7 KiB) TX bytes:433068 (422.9 KiB) wlan0-1 Link encap:Ethernet HWaddr 02:C0:CA:91:6F:22 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10329 errors:0 dropped:0 overruns:0 frame:0 TX packets:10014 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1681829 (1.6 MiB) TX bytes:3884867 (3.7 MiB) --------------------------------------------------------------------- After connecting wifi adapter root@Pineapple:~# iwconfig lo no wireless extensions. wlan1 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm RTS thr:off Fragment thr:off Encryption key:off Power Management:off wlan0-1 IEEE 802.11bgn Mode:Master Tx-Power=17 dBm RTS thr:off Fragment thr:off Power Management:off wlan0 IEEE 802.11bgn Mode:Master Tx-Power=17 dBm RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. br-lan no wireless extensions. root@Pineapple:~# ifconfig br-lan Link encap:Ethernet HWaddr 00:C0:CA:91:9E:0B inet addr:172.16.42.1 Bcast:172.16.42.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11389 errors:0 dropped:1591 overruns:0 frame:0 TX packets:9965 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1701888 (1.6 MiB) TX bytes:4256316 (4.0 MiB) eth0 Link encap:Ethernet HWaddr 00:C0:CA:91:9E:0B UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:4 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:660 errors:0 dropped:0 overruns:0 frame:0 TX packets:660 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:56828 (55.4 KiB) TX bytes:56828 (55.4 KiB) wlan0 Link encap:Ethernet HWaddr 00:C0:CA:91:6F:22 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:30 errors:0 dropped:0 overruns:0 frame:0 TX packets:3095 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2805 (2.7 KiB) TX bytes:445120 (434.6 KiB) wlan0-1 Link encap:Ethernet HWaddr 02:C0:CA:91:6F:22 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12426 errors:0 dropped:0 overruns:0 frame:0 TX packets:12395 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2079498 (1.9 MiB) TX bytes:4921454 (4.6 MiB)

Hi Tried configuring the mentioned adapter. It doesn't show up in the client mode. Also, I don't see any new entry in iwconfig :( If this requires drivers to be updated manually, but i am not able to get the step on how to do the same. Appreciated your prompt response, it will be of no use to me if i cannot get wifi attached to this. USB theathring is something i cannot do always as the data is limited. And extending the WIFI as theatring doenst seems to be working on my mobile device.

The device i am using is http://www.amazon.in/Terabyte-Wireless-Connector-Manufacturer-INFOTECH/dp/B01N28PJAN?_encoding=UTF8&deviceType=desktop&psc=1&redirect=true&ref_=oh_aui_detailpage_o00_s00

Thanks for the prompt response. I am not able to see wlan2 as an option in nano. Navigated to Networking -> wifi client mode -> and i only see wlan1. Does it mean that the wifi attached was not detected? I am able to use the wifi device in my windows.

Yup... Spot on.

Hi Experts, I got my nano basic only today. It works like a charm with usb tethering with my andriod connected. I have few questions listed below 1) I'm unable to configure mini wifi instead of using usb tethering. And unable to find a guide to configure the same on Google. 2) the management console doesn't seems to work on other devices. Tried connecting the management ap over my laptop but the console is inaccessible. I want to configure the home wifi with the mini wifi usb im connecting to pineapple and use any other device to access the management console to view the readings and run modules