Active Members
  • Content count

  • Joined

  • Last visited

About esa

  • Rank
    Hak5 Fan +
  1. Nano/Tetra networking module with more options for client AP creation. WEP/WPA/WPA2, Disable AP Installation: Just place the files in /pineapple/modules/NetworkingPlus Alternative installation: Replace the files with those on the /pineapple/modules/Networking Do a refresh of pineapple gui management console. Allow Associations **Client AP is also being use by PineAP. So this might disrupt how Pineapple Wifi Works. Reset back to any open AP if you are experiencing issues with other modules. Not tested thoroughly, please highlight if you are facing issues with this. Will try to debug it for the benefit of the community. Intention for creating this is to make my life easier when performing Evil Twin against clients on WPA2/WPA protected APs.
  2. I have been using a trial version of JetBrains WebStorm for development of some Nano/Tetra modules. Unfortunately the trial is expiring & it is a costly product @129USD for a year's license. Any modules developers can recommend something good that you are using? Requires support for html, angularjs, python, php.
  3. Was looking for the same function. Couldnt find it so i just modded the networking module instead. Surprisingly straightforward mod < 5 lines of codes. Copy the files and replace the files in the original networking module. Do highlight if it works or there are any bugs.
  4. my bad there is a missing folder in my git upload. Please create a folder called "log" in the module's directory. It should work after that. cd /pineapple/module/ReconPlus mkdir log For others who intend to install in their sd card. transfer ReconPlus to /sd/modules/ReconPlus and remember to create the softlink. ln -s /sd/modules/ReconPlus /pineapple/module/ReconPlus
  5. 1) I can easily power my Nano without both usb connection plugged in. I connect it straight to my laptop. 2) It is a pain in the arse to get internet on Windows, somehow it always forget my settings. a) Ensure that you have internet b) connect your pineapple to your pc and wait till the blue led are solid or the portal is up c) On your main internet interface->properties->sharing turn off internet sharing and wait 10 sec. d) On the same tab select your pineapple interface and turn on internet sharing, wait 10 sec. Close tab by clicking ok. e) On your pineapple interface -> properties -> networking select the IPv4 & enter the ip address f) Now you pineapple should have internet. Else disable your pineapple interface, enable it again and repeat steps (c) to (e)
  6. 1 solution. Use your phone to connect to SBUX wifi then "accept and connect" thru the phone's browser. Now that the phone has internet, turn on usb tethering and connect your pineapple to the phone using usb connection. Dun forget to download the wifi pineapple apk for easy access to your pineapple's management console. **Dont think there is an easy solution to an offline captive portal. Good luck hf.
  7. this is strange, doesnt sound like a faulty hardware since you can get it to work occasionally. try this and report any errors faced: 1) restart your pineapple 2) ssh to it 3) Start wlan1 as monitor mode using airmon-ng airmon-ng wlan1 start 4) Perform airodump using your wlan1mon interface. you should expect to see some MAC addresses in your vicinity airodump-ng wlan1mon 5) This performs the same command as running recon on 2.4ghz for 1min. The results will be stored in /tmp/re pinesniffer wlan1mon 60 1 /tmp/re 6) Read /tmp/re, you should expect some results cat /tmp/re
  8. Can you elaborate why this setup is not ideal? If it is not working, try using as the destination ip.
  9. Depends on your needs. By default (using GUI) wlan0 is responsible for AP while wlan1 does sniffing and injection. If you want to create a free rogue AP, then connect to wlan0. If you want to monitor/sniff then connect to wlan1. If you want to deauth a device and force it to connect to your AP, then you will need both.
  10. A simple Sunday project.
  11. Try a factory reset.
  12. Okay try using this
  13. 1) Devices that connect to your Pineapple AP, do they have internet? 2) Use br-lan 3) On the devices browse to a number of http websites 4) It should work
  14. On DNSMasq, modify the host file as such * modify the landing as such <html> <head> <title>PHP Test</title> </head> <body> <?php echo '<p>Hello World</p>'; ?> </body> </html> 1) Connect your device to a AP generated by Pineapple 2) Ensure that your device has internet after connecting to the Pineapple AP 3) Start DNSMasq Spoof. 4) Close all browsers/delete cache 5) Surf to any website. Only 1 of 2 outcome if ur DNSMasq works a) you see a Hello World on the browser b) The browser refuses to connect due to HSTS
  15. no module for it yet. but you could ssh into pineapple and create a WPA/WEP AP. modify the hostapd file accordingly for WPA/WEP. WEP network still exist ? rarely see it around,